[New User] Using Minicom and a USB/Serial cable to talk to your KPC 3+

Over the weekend, I was showing Linux and Packet radio and for some reason I could not talk to my TNC, a KPC 3+. It was at this point that I realized I had forgotten more about Linux (and minicom) than I had about the commands needed to control the TNC. So, in the interest of helping save you some time, here is a quick write up on using minicom with a USB/Serial adapter to talk to your TNC, specifically, a KPC.

Minicom is an old school program that is available for most of the distributions but may not be installed by default. The good news: it is in all the repositories, so you can pull it down and install it quickly.

It is a serial terminal program that runs from the command line, but can sometimes be a little fussy to get working, and I will admit that I have not used minicom with a USB/Serial converter.

First, you have to know what tty port your USB/Serial converter is
on. So, plug it in, give it a minute and then type at a console port:

dmesg | grep tty

You should get something like this back:


kg4giy@kauai:/$ dmesg | grep tty
[ 0.001982] console [tty0] enabled
[ 686.529224] usb 2-2: pl2303 converter now attached to ttyUSB0

In this case, the converter is attached to ttyUSB0, you when you
configure minicom, you want to use /dev/ttyUSB0 as the serial port
setting.

To start minicom then (assuming you have not configured it, but you
know the modem speed of the TNC) type:

$ sudo minicom -s

Note that minicom requires root privileges. You will be prompted for
your password.

Select "Serial port set up" from the list with the cursor keys and set
the serial device and the Bps/par/bits (8/N/1 and whatever the speed
of your TNC is). Press , Save setup as dfl to save your
settings and then select Exit to enter minicom.

Turn on the TNC. Press once or twice if you do not get the
TNC cmd: prompt and you should now have control of the TNC.

When you are done, A then Z will bring up the help menu and you
can exit by pressing Q or A Q to exit.

One thing to note. Minicom has a much smaller set of connection speeds. For overall interoperability, it is best to set the baud rate of your TNC to 9600, with 8-n-1 for parity. This will facilitate connectivity with a multitude of devices, including a simple VT220.

I hope this saves you all a few minutes!

Idea for writing amateur radio software

KB2YUI's picture

Although I do not know a lot about writing code (I took Computer Programming with C++ a few years ago back in college.) I would like to find some interested people in writing a new Linux program-a collaberated effort if you will. Some one smater than me would have to sort of Elmer me through it.

I am wondering if it is possible to write a program that will control the XCVR and TNC as well as run the software and do logging all in one package. In other words do every thing through the computer like an SDR with data link. It sounds half baked and crazy I know, but it is something that I have thought a lot about lately as to if is feasible as well as possible.

If this sounds like anything that can be done and some one is interested in please let me know. THANKS and 73's!

Webinar
One Click, Universal Protection: Implementing Centralized Security Policies on Linux Systems

As Linux continues to play an ever increasing role in corporate data centers and institutions, ensuring the integrity and protection of these systems must be a priority. With 60% of the world's websites and an increasing share of organization's mission-critical workloads running on Linux, failing to stop malware and other advanced threats on Linux can increasingly impact an organization's reputation and bottom line.

Learn More

Sponsored by Bit9

Webinar
Linux Backup and Recovery Webinar

Most companies incorporate backup procedures for critical data, which can be restored quickly if a loss occurs. However, fewer companies are prepared for catastrophic system failures, in which they lose all data, the entire operating system, applications, settings, patches and more, reducing their system(s) to “bare metal.” After all, before data can be restored to a system, there must be a system to restore it to.

In this one hour webinar, learn how to enhance your existing backup strategies for better disaster recovery preparedness using Storix System Backup Administrator (SBAdmin), a highly flexible bare-metal recovery solution for UNIX and Linux systems.

Learn More

Sponsored by Storix