Protecting Files at Home Using Encrypted Containers

Many people encrypt partitions or drives to keep data safe, but if you're looking for something a little simpler but still safe, try using containers.

Chances are you have some type of information on your desktop or laptop computer that someone else wants--for the wrong reasons. For the most part, your information is relatively safe in your home. However, if someone was to break into your house and steal a computer, what would he or she walk away with? Medical information? Bank account information? Tax records? With the loss of any of these to the wrong person, you could be facing years of trying to get your life straightened out due to identity theft.

Concerned about this type of situation, I decided to engineer a way of protecting my family's critical information. But before I started, I had to set a few goals for whatever it was that I built:

  • It had to be as simple as possible to use.

  • Data loss was not acceptable.

  • The data had to be protected even if a computer physically was stolen.

The first goal, simple to use, was absolutely necessary. I wouldn't be the only one using the system, so it had to be geared toward someone non-technical. Setting it up could be difficult, but in the long run it wouldn't be used or useful if the solution itself was difficult. Data loss also was an important criterion. Protected data is worthless if you have no way of getting it back in the event of a hard drive failure. The last criterion was the main point of doing this whole project: if a computer was stolen, how long would it take before I could get a full night's sleep knowing that someone had access to all the information necessary to steal the identity of one of my family members?

Once my goals were set, I went about researching my options and evaluating ideas. I finally settled on using an encrypted "container" that could function like any other storage device, but only when needed. To prevent data loss, it would be backed up to my home server. On the home server, the same technology would be used to protect my backups and where I centrally could burn a CD or DVD for off-site storage.

The first step to protecting my data was to figure out how to create an encrypted container. After doing some research, I discovered there were two ways to do this. I could use either cryptoloop or its successor, dm_crypt. A considerable amount of information is available for using cryptoloop, but I quickly discovered that it has been deprecated and replaced by the more secure dm_crypt kernel module.


To complete the encrypted container configuration presented in this article, you must satisfy the following short list of prerequisites:

  • Kernel version 2.6.4-rc2 or higher must be installed.

  • KDE version 3.3 or higher must be installed.

  • You must have root access to complete the initial setup.

I currently am running this configuration under kernel version 2.6.12 on several Gentoo systems, both x86 and AMD64. I also have used it on kernels starting around version 2.6.6. The scripts I present here for making the system easy to use have been used under KDE versions 3.3.x and 3.4.x. Older versions of KDE also may work, but they have not been tested by me.

Configuring Your System

To use dm-crypt, a few modules must be compiled or built into the kernel. You first must enable the device-mapper module that lets you create new logical block devices from portions of existing devices. The block devices then are "mapped" to devices that for our use are treated like normal drive partitions. Once device-mapper is enabled, you then can enable dm-crypt itself; it goes by the name Crypt Target Support in the kernel configuration menu. dm-crypt is the kernel module that we actually use to handle the encryption/decryption using the crypto API available in the 2.6 version kernels.

To use an encrypted container for our files instead of an entire drive or partition, loopback device support also needs to be enabled in the kernel. The loopback device kernel module allows us to use ordinary files as if they were real block devices. Finally, you must have the encryption type you want to use compiled into the kernel or set as a module. In the examples given here, I use the AES encryption algorithm, but many other options are available.

Once you have enabled the required kernel modules, compile the kernel and install it. Because I did not build the modules directly into the kernel, I added the necessary modules--dm-mod, dm-crypt and aes-i586--to /etc/modules.autoload/kernel-2.6 on my Gentoo boxes so they would be loaded automatically at boot. Below is a list of kernel modules you need to enable in the kernel:

Device Drivers -> Multi-Device Support (RAID and LVM) -> Device Mapper Support
Device Drivers -> Multi-Device Support (RAID and LVM) -> Crypt Target Support
Device Drivers -> Block Devices -> Loopback Device Support
Cryptographic Options -> <encryption type>

For other systems where there may not be a central location to load kernel modules automatically at boot, you could add the appropriate modprobe commands to a startup script. For Debian-based systems such as Ubuntu, the script to use is the /etc/init.d/ startup script. For other distributions you can use /etc/init.d/rc.local. Here are suggested commands to add to startup scripts for non-Gentoo distributions:

modprobe dm-mod
modprobe dm-crypt
modprobe aes

Now that the kernel has been configured, two packages must be installed that will be used to ease the creation and use of the encrypted container as a device. The first package you need to install is the device-mapper utilities. Under Gentoo, simply executing emerge device-mapper automatically downloads, compiles and installs the package. It already may be installed in other Linux distributions. An easy way to tell if you already have the device-mapper package installed is to look to see if /dev/mapper and /dev/mapper/control already exist. If they do, the device mapper is installed. Otherwise, for Debian-based systems such as Ubuntu, you can execute apt-get install libdevmapper. If you're using a different distribution, check your package management system and see if it can be installed easily. If not, refer to the Resources section for a link to where you can download it directly.

The second package you need to install is the cryptsetup utility. Under Gentoo, it can be installed by executing emerge cryptsetup. Again, if you are using a different Linux distribution, cryptsetup already may be installed for you or available through the package management system. You can determine if the package already is installed by checking to see if the cryptsetup command is available, most likely in the /bin directory. Otherwise, refer to the dm-crypt listing in Resources for the link to the download.

Creating the Encrypted Container

After rebooting with your new kernel, you are ready to create the container for your files and mount it. Select a partition with enough space to create the container and make the container large enough to support all the files you want to put into it. Don't forget to make it large enough to hold new files. Keep in mind that at the time this article was written, it was not possible to increase the container size once it's created. Instead, you have to create a new, larger drive container, copy everything from the old one to the new one and then delete the old container.

To create the container file, use the dd command; it typically is used to copy drive partitions. In the example below, I specified a block size of 1MB and that the container should be 2,048 blocks in size. This equates to a container that is 2GB in size--1MB block size X 2,048 blocks.

As a source for the dd command, I used a special device that outputs nothing but zeros when read. Others have suggested that using /dev/random may be better, because it makes it impossible to determine how much of the container actually is being used. The choice is up to you. I also used a partition (/encrypted) that I set aside specifically for storing my containers.

dd if=/dev/zero of=/encrypted/data.crypt bs=1m count=2048

Now, create a loopback device using your container file. If you use multiple containers, you have to use a different /dev/loopX device--where X is a unique number--if you want them all to be mounted at the same time. I chose to put specific containers on specific numbers in my scripts (details below) so I know which one is using which loopback device.

losetup /dev/loop0 /encrypted/data.crypt

Next, create the encrypted device. In the example given below, I chose to use the AES encryption algorithm, which was compiled as a kernel module during kernel configuration. When the device is created, you must specify a password, otherwise known as a key, that is used to encrypt and decrypt everything in the container. This can be a secure password that you specify on the command line. In my case, I used /dev/random to generate a 32-character random string (256 bits) that I stored in a file named /home/pritchey/crypto.key temporarily; more on this later.

cat /dev/random > /home/pritchey/foo (hit control-c after a second goes by to stop it!)
cat /home/pritchey/foo | cut -b 0-31 > /home/pritchey/crypto.key
rm /home/pritchey/foo
cryptsetup -c aes -d /home/pritchey/crypto.key create data.crypt /dev/loop0

You now have something that acts like a normal drive partition. In order to mount and use it, you must create a filesystem on it. I chose to use the ext2 filesystem, but others can be be used. Once the filesystem is created, it can be mounted like a regular drive partition.

mke2fs -j /dev/mapper/data.crypt
mkdir /mnt/encrypted
mount /dev/mapper/data.crypt /mnt/encrypted

Once mounted, your encrypted device acts the exact same way that a normal drive partition does. You can copy files to it, delete them, edit them and so on. The only difference is you must remember to unmount the device properly and destroy the loopback setup when you are done with it:

umount /mnt/encrypted
cryptsetup remove data.crypt
losetup -d /dev/loop0

Getting access to your files in the future requires three simple steps:

losetup /dev/loop0 /encrypted/data.crypt
cryptsetup -d /home/pritchey/crypto.key create data.crypt /dev/loop0
mount /dev/mapper/data.crypt /mnt/encrypted

This solves the problem of protecting our data. But, for non-technical users, these commands are difficult to remember and scary looking--not to mention they require root access. The next step is to automate the mounting/unmounting of the encrypted containers in a way that is easy to do yet not obvious to someone who might not think to look for them.

Automation Creation, Part I

To automate the mounting/unmounting of the encrypted container, I turned to my favorite search engine and a coworker. The problem I encountered when trying to create a script for the above commands was root access is required to set up everything. I wanted others in the house to be able to use the encrypted containers, but they're not experienced enough yet to be trusted with root-level access. Carlos, a co-worker, once had to solve a similar problem that required root access to run a script, yet didn't warrant the use of sudo. He found a Perl script that did the trick when the sticky bit was set, essentially acting as a wrapper around the real script. I searched the Web and couldn't find the Perl script, but I did stumble upon exactly what I needed: a tiny program written in C that acts as a wrapper (see Resources) around a script that needs root privileges. All that was required was changing the commands the program was supposed to run, compiling the program and copying it into place with the sticky bit set.

To use the wrapper, you need to change three values before compiling it. First, set the variable myprog to the script that you want to execute. The second variable, named myarg1, contains the name of the loopback device (/dev/loopX) to be used. The last variable, myarg2, is set to the name of the container that you want to mount. For my naming scheme, I add a .crypt to the end of my container file names. I also named my key files in a similar manner, ending them with .key. Here is the C source code for wrapper.c:

    #include <stdio.h>
    #include <unistd.h>

    const char myprog[] = "/bin/encrypt_mount_gen";
    const char myarg1[] = "loop0";
    const char myarg2[] = "data";

        putenv("IFS= \t\n");
        execl(myprog, myprog, myarg1, myarg2, (char*)0);
        fprintf(stderr,"Could not execute %s\n",myprog);

Once the appropriate changes are made, compile the program, copy it into place and be sure to set the permissions correctly. I chose to create a special group in /etc/group only for users that should be able to mount the encrypted container (named crypto). The permissions and ownership of the directory the encrypted device is mounted to, created in a previous step as /mnt/encrypted, is also set this way. This prevents other users who have accounts on the computer from mounting or accessing the encrypted devices.

    gcc -o mysecretcommand wrapper.c
    cp mysecretcommand /bin
    chown root:crypto /bin/mysecretcommand
    chmod 750 /bin/mysecretcommand
    chmod u+s /bin/mysecretcommand

    #To protect mounted encrypted data:
    chown pritchey:crypto /mnt/encrypted
    chmod 770 /mnt/encrypted

To handle unmounting the encrypted containers, you need to use the wrapper program again--named encryptoff in the sample scripts. This time, though, it calls a script containing the appropriate commands to undo the encrypted container. Here is a sample script for unmounting a mounted encrypted container:


    /bin/umount /mnt/encrypted
    /bin/cryptsetup remove data.crypt
    /sbin/losetup -d /dev/loop0
    #Repeat the above three commands for each encrypted container....

Automation Creation, Part II

The script called from the above wrapper is written so that when called with two parameters, it would be able to mount any encrypted container. That way I could have as many wrappers as needed that are unique to each specific encrypted container but only have one script that actually performs the mounting and unmounting. The script assumes that the encrypted container ends in .crypt and the key file ends in .key, but both have the same beginning name that's passed as the second parameter.

To help increase security, I also decided to store the key (password) used for the encryption device on a USB thumb drive. It's never a good idea to store passwords in files, but in this case the key is impossible to remember. As long as the thumb drive is kept separate from the computer it belongs to--locked in a safe, for example--it would be an adequate solution. If the computer is stolen, the likelihood of the thief taking the USB key along with the computer and knowing what to do with it is small. And with a 256-bit (32-character) key, the system would be difficult to crack by brute force methods.

So the automation script also is responsible for mounting the USB thumb drive and unmounting it when done. This minimizes the amount of time the thumb drive needs to be connected to the computer. Hopefully, this helps minimize the chances of someone leaving it connected, as the drive can be removed immediately after logging in (detailed later).

Here is the encrypt_mount_gen shell script called from the wrapper:


    /bin/mount /mnt/usb_stick
    /sbin/losetup /dev/$1 /encrypted/$2.crypt
    /bin/cryptsetup -d /mnt/usb_stick/$2.key create $2.crypt /dev/$1
    /bin/mount /dev/mapper/$2.crypt /mnt/encrypted_$2
    /bin/umount /mnt/usb_stick

This design partially solves the ease of use requirement, but it still requires someone to remember a command, which could be named anything I want in order to hide it. I had an idea, and searching the Web revealed that KDE has two special directories that can contain scripts or links to executables the user wants run when he or she first logs in or out. Every user's home directory contains a hidden directory named .kde. This is where the two directories used for login/logout are located. The directory used on login is called Autostart, note the capital letter A. Simply place a script here that executes as many of your wrappers as needed. Here is the sample script I placed in my /home/pritchey/.kde/Autostart directory:


Similarly, we can use the directory .kde/shutdown with another script to unmount and clean up automatically any encrypted containers. This is the final piece that solves the ease of use issue. To use the system, all you need to do is power on the computer, plug in the USB thumb drive with the keys to the encrypted containers and log into KDE. Once logged in, unplug the thumb drive and return it immediately to its hiding spot. If you log in before remembering to plug in the thumb drive, you either can log out and back in again with the thumb drive attached or execute the wrapper command from a shell prompt.

Almost Done

One remaining requirement needs to be addressed: protecting ourselves from data loss. I had solved this problem before, so it simply was a matter of integrating the encrypted containers into my backup system. All of my systems are set to back up users' home directories when they log out of KDE, which is triggered by a script in .kde/shutdown. All I needed to do was modify the script to handle the encrypted containers when they are mounted. This script executes rsync and saves any changed files to a server. I modified the backup script to take parameters specifying the directory to be synced. The default is to sync the user's home directory with the backup location on the server. The script in the user's shutdown directory then was modified to detect if the encrypted containers were mounted and if so, rsync it before unmounting. Syncing the mounted data is much faster than trying to sync the large container file itself, even on a quiet home network. Here is the script I placed in /home/pritchey/.kde/shutdown:


    # Look to see if our encrypted partitions have been mounted
    # and if so back them up before unmounting them.
    is_projects_mounted=`df | grep encrypted_projects`
    is_encrypted_mounted=`df | grep encrypted | grep -v projects`

    if [ "$is_projects_mounted" != "" ]; then
        /home/pritchey/scripts/ /mnt/encrypted_projects
    if [ "$is_encrypted_mounted" != "" ]; then
        /home/pritchey/scripts/ /mnt/encrypted

    # Now that they have been properly backed up, umount the
    # encrypted partitions.  Call the wrapper that calls the 
    # script with the commands to 'undo' the mounted containers.

    # Now backup non-encrypted data so we have an off computer backup.

And here is the general purpose directory backup script referenced in my KDE shutdown script:

#! /bin/bash -x
# This script performs a very simple backup of the user's home directory
# by default (if no parameters are passed).
# This script is meant to be referenced in the user's ~/.kde/shutdown directory
# If parameters are passed, then they are used as follows:
#       Parameter 1:  Used as the base directory to be synced.
#       Parameter 2:  Used as the 'ignore' list of directories/files
echo "------------" >> /tmp/rsync.log
echo "starting" `/bin/date` >> /tmp/rsync.log
# make sure we're online and have access to our backup server...
if [ `ping -c 1 | grep '64 bytes from' | wc -l` -eq 1 ]
   if [ "$1z" == "z" ]; then

   /usr/bin/rsync -vauR --delete --stats --exclude="$EXCLUDE_DIR" 
	"$BACKUP_DIR" rsync://
   echo "Rsync for: $BACKUP_DIR succeeded" >> /tmp/rsync.log
   echo "Rsync for: $BACKUP_DIR FAILED" >> /tmp/rsync.log

     echo "completed" `/bin/date` >> /tmp/rsync.log

Final Notes

I have read many articles on encrypting entire partitions and drives, but I chose to use containers instead. By using containers, I have the flexibility to move them around, back them up to CD or DVD and not mount them when I don't need them. If the situation was different, I may have chosen the route of using encrypted partitions or drives. In the beginning I also was concerned about the performance impact of using an encrypted system. In a year's worth of use, though, I have not noticed any performance problems.

The backup script I use obviously can be expanded to be much more robust. For my home use, it's proven to be reliable enough. But in a work environment, I would take the time to add additional safety checks. I also chose not to go into too much detail here about the use of rsync. Many good articles detailing the use of rsync are available, and you might decide to use another method for performing backups.

In order to complete the protection of my systems, I also have included the commands used to unmount the encrypted containers in the system shutdown scripts. This way, if a system is shutdown remotely or the UPS software shuts the system down, the encrypted containers are unmounted properly and cleanly.

I would like to thank Carlos for the pointer to the idea of using an suid wrapper and Darryl for testing the scripts and installation procedure presented here. I have enjoyed working with both of them over the years, and they have proven to be great resources of information for things nobody else can figure out.



Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.

Using partitions and file containers

GooHackle's picture

Here's another couple of very good tutorials to do it.
Over a file or a partition:

How to create a LVM encrypted partition

How to create a portable encrypted file system on a loop file

Some help with loopback devices

Anonymous's picture

The scripts given here can be helped by use of the following functions:

# Find an available loopback device.
# Answer returned in variable loopdev.
function find_loop()
 for l in /dev/loop* ; do
  losetup $l 2>&1 | grep -qv "^$l:" && loopdev=$l && break
 [ "$loopdev" ] || {
  1>&2 echo "Could not find available loopback device"
  exit 1

# Find loopback device used to mount file given in $1.
# Answer returned in variable loopdev.
function find_loop()
 line=$(losetup -a | grep "$1")
 [ "$loopdev" ] || {
  1>&2 echo "Could not find loopback device for $1"
  exit 1

Change Loop Line

Ben's picture

The for loop in the first method (find_loop) should not be:
for l in /dev/loop* ; do

But rather should be
for l in /dev/loop? ; do

Otherwise you will get the directory /dev/loop to be returned as the free loop because of the way this snippet checks to see if this loop is unused.

Just thought I'd throw that out there.

Function Names

Anonymous's picture

If you are going to put those functions in the same script you should give them different names. In my case I use them in different scripts so it didn't hurt to give them the same name. YMMV.

Author Responds

pritchey's picture

First, I'd like to thank all of you who have taken the time to read the article, and especially those who have taken the time to respond.

Rather than respond to each individual comment, I'll post my comments in this single post instead since there seems to be just a few themes...

1. KDE is not needed. KDE Just happens to be my current desktop of choice and in order to meet the requirements I set my solution to the problem needed to be integrated into it (primarily for other family memebers who are less technical). And no, I am in no way associated with the KDE project :-) I've used Gnome, Enlightenment and KDE at various times. KDE just happens to be the one in use right now.

2. The key is NOT stored on the hard drive, down towards the bottom of the article I present a few scripts that I use that execute everything based on the key being on a USB thumb drive. Most thiefs probably wouldn't know what to do with a linux box if they stole one, but I did decide to go the extra step and keep the key on something physically separate rather than rely completely on security by obscurity.

3. Brett Neumeier provided a much more elegant solution to generating the key from /dev/random by using the dd command. Thanks you! I keep forgetting about that command, much less the fact it would have made key generation easier!

4. LUKS as an alternative: Thank you for posting about this project. I wasn't aware of it before. Unfortunately when I actually implemented this LUKS didn't exist at the time.....

5. Dave Vehrs posted a warning that the commands used to mount/unmount the encrypted containers may appear in your shell's history. That is correct, if you issue the commands by hand. I just checked and the commands do not appear if you use the automated capability provided by the KDE Autostart and shutdown directories. For many, encrypted the entire drive may be a better solution. In my case I decided that wasn't the solution I needed and chose to go the encrypted container route.

6. There was a comment about my backups. My backup server is using the same setup - the backups reside in an encrypted container that gets 'undone' on shutdown automatically OR undone on startup in the event the power cord is pulled. There is NO automation on the backup server to automaticaly remount the encrypted containers, and the server is locked down tight (as are the desktop boxes). The only item I'm missing is performing the rsync over an SSH tunnel, which for a home hardwired network isn't really necessary. Keep in mind, this is meant to provide adequate protection for a _home_ environment. For a work environment I would do some things differently in order to provide a more robust system, but those items are beyond the scope of this article.

7. Thank you for reminding me about ENCFS. I seem to remember looking at it when I started implementing this, but I can't remember why I decided not to use it. It is definitely worth looking at though.

Again, thanks to everyone that has replied so far!


Just a few observations for t

Nelson's picture

Just a few observations for the new user trying to implement this in Fedora Core 3.

1- The use of /dev/random for some reason does get the job done. I tried and it stopped at some point but didn't get what I wanted in size. So I used /dev/zero as suggested by the article.

2- cut will not cut exactly 32 bytes, so instead I used
head -c 32 foo

3- dd didn't take the bs=1m, the m has to be capitalized, like this bs=1M

4- cryptsetup is not in /bin but in /sbin so change scripts accordingly.

5- You don't need KDE in order to run the scripts when the session starts and finishes. You can do same thing from the file in your home directory called .Xclients
Just add it before and after this part:

exec $HOME/.Xclients-default

And you should be done. If you don't have that file, use the program


and it will create it.

If you want to do it permanently for all users and new users, modify the "template" file found in /usr/share/switchdesk/Xclients.toplevel

Don't use /dev/zero.

Anonymous's picture

Don't use /dev/zero. /dev/random didn't work for you because you didn't have enough entropy. Use /dev/urandom instead.

/dev/zero is less secure than /dev/(u)random.

Several errors

Peter Hoeg's picture
  • KDE has nothing to do with this solution and is not needed
  • You store the key directly on your pc and it is trivial for an attacker to decrypt the container

It is basically security by obscurity which everybody agrees does not work. This "solution" is not safe.

Re: Several Errors

Anonymous's picture

Comments on your two items:

1. You are correct. KDE is not needed. But it does show a way of integrating it the whole process using the startup/shutdown capability provided by KDE on login. The same idea could be used for other desktop environments or even terminal logins (via the default shell's config files).

2. You are incorrect. Under the section titled Automation Creation, Part II 2nd paragraph the author states that he is using a USB thumb drive to store the key which is kept physically separate from the computer.

Protecting the key from theft along with the computer?

Anonymous's picture

This is something I need to give more thought to before I try to implement a transparent encryption scheme on my own computers.... but the skeleton given here is a great starting point, thanks!

The main flaw in the design I see, is this. Ignoring the "security boundaries" arguments for a moment (or assuming this has been solved by control) -- that is, even assuming that your sensitive data never leave the container in a cleartext form:

How exactly does this protect your data from a thief?

The encryption key has been left on the computer along with the containers! Can't the theif just take the hard drive out, mount it in their own system, discover the encrypted containers, these mounting scripts and the key and then mount the containers to get at the data? Sure, this would take a clueful thief, probably not something your average house-breaker could manage, but well within the abilities of an experienced identity-theft criminal.

I would have liked to see a way of keeping the key safe from being stolen (or discovered) along with the computer, such as on a USB drive or a floppy, or by encrypting the key with a pass-phrase.

These approaches are not perfect either, I admit: you have to remember to insert and remove the medium containing the key, or enter a pass-phrase to decrypt the container key before mounting, which would break the "simple to use" requirement, I suppose.

Don't create the key on disk

Anonymous's picture

In your example you create the key file on the disk

cat /dev/random > /home/pritchey/foo
cat /home/pritchey/foo | cut -b 0-31 > /home/pritchey/crypto.key
rm /home/pritchey/foo

Assuming that /home is mounted on a physical disk, both foo and crypto.key are on disk and the rm command does not remove them from disk. (rm simply removes the pointers. The data is still on disk and easily recovered.) If You must create the key files on disk you need to use wipe rather than rm to clean them off your disk. A better idea is to create them on a USB drive in the first place.

Read the section Automation C

Anonymous's picture

Read the section Automation Creation, Part II. A USB thumb drive is used for storing the key, and the scripts provided handle the automounting of the USB drive, mounting the encrypted container and then unmounting the USB drive so it can be removed from the computer and put back to its hiding place.

unnecessary /dev/random contortions

Brett Neumeier's picture

rather than doing:

cat /dev/random > /home/pritchey/foo
cat /home/pritchey/foo | cut -b 0-31 > /home/pritchey/crypto.key

it is way simpler just to do:

dd if=/dev/random of=/home/pritchey/crypto.key bs=1 count=32

Have a look at LUKS before do

Anonymous's picture

Have a look at LUKS before doing everything by hand as suggested in this article. Additionally LUKS has sophisticated key management features, e.g. it is possible to define multiple keys for a container.

Be careful with containers.....

Dave Vehrs's picture

You have to be very careful when you use encrypted containers because you will often leave evidence of their existance and mounting/unmounting in your shells history.

For Bash, to prevent certain commands from being recorded in the history, just configure the HISTIGNORE variable like so:


Or your could just encrypt the entire system so that everything is protected. For an example of this, check out:

GPG to store the container key

Yann Droneaud's picture

I wrote some small scripts to use a GPG file to hold the encryption key. Doing so, I can change the passphrase used to unlock the container without reencrypt all the container.

Check them via Archzoom browser.

Those scripts are used at boot time to unlock my LVM volume group where my real Linux system reside.

There's some comments about meta data associated to a container like algorithm, offset, etc, but it's still not implemented.

Check GDBE(4) for some pointers on idea about the meta data.

Security Breakdown

Anonymous's picture

I might be missing something but when you rsync the files to your server they are mounted and unencrypted. This means unencrypted copies of your files are sitting on the server. What happens if someone takes the server instead of the laptop or if the server is compromised in some other way.

Security? Really?!

Janis's picture

About what security we can discuss, if the crypto key is stored in the FILE residing on THE SAME system?! Or for the storage of crypto keys other crypto storage is intended to be made? (it seems that LUKS also is not storing the keys necessaary to access the respective crypto device which is right by my understandig of how the crypto-things works)

Re: encrypted containers

Anonymous's picture

Funny, I implemented almost the same solution to burn encrypted DVDs.
Here are some things I encountered that other users might hit when they try this at home:

  1. Container sizes are fixed, and existing containers cannot be resized. Especially when making backups you must know the overall backup size before creating the container.
  2. Filesize limits for the container file. Most filesystems have limits to filesize, especially the filesystem type used for DVDR and CDR (iso9660) is 4G. Well, in reality the limit depends on your hardware and/or software. But on my system 4G files work. So you should not use too large containers if you want to be able to burn it to DVD.
  3. The key file (crypto.key) is small, but very important. I am storing multiple copies of the key file for redundancy since I burn the stuff to DVD, and one of the key files might get corrupted.

    There is a nice new format called LUKS which stores the key redundant in the container. I have not tried it yet though.

I really like the encfs files

Anonymous's picture

I really like the encfs filesystem. It's secure, transparent,and does not require root privs to use (or KDE ;-).


Pollywog's picture

The article was very interesting but I was disappointed that root privileges are required to use the methods given.

As I worked on putting this together, I noticed the comment about encfs and Xandros has the package, so I am going to see if I can get that to work. Thanks for the info on encfs.

Another way of avoiding root

Anonymous's picture

Another way of avoiding root privileges is to use the utility "cryptmount" (see here), which allows setup of device-mapper targets for both raw partitions and looopback files. Root privileges are only needed for the initial setup, and dm-crypt keys are stored in encrypted form (using openssl).

This doesn't require KDE

Anonymous's picture

The core of this doesn't require KDE nor any GUI tools at all.

Silly writer! No sucrose-encrusted toroidal pastry!

KDE people run a con every we

Anonymous's picture

KDE people run a con every week to get people to install KDE. This type of thing happens once a week, it's worth a chuckle, just ignore it.