Benchmarks for Native IPsec in the 2.6 Kernel
IPsec is an addition to IP protocol that allows authentication and encryption of IP datagrams. It is defined in detail in IETF RFCs 2401, RFC 2402, RFC 2406 and RFC 2407 (see Resources). IPsec can be used to secure a rather wide range of scenarios; one of its best-known usages is creating virtual private networks (VPNs). A VPN is a secure, private tunnel between two sub-networks using encrypted communication over the Internet.
FreeS/WAN has been the main IPsec implementation for Linux for a long time. Unfortunately, FreeS/WAN has never been integrated into the Linux kernel itself. Instead, the new native kernel IPsec implementation is based on the KAME project, a part of the UNIX/BSD family.
The USAGI project used the BSD code from the KAME project as a base for integrating IPsec into the Linux kernel. KAME's user-space tools, specifically setkey and Racoon, have been ported to Linux by the IPsec-tools Project (see Resources).
In this article, we implement a simple scenario of setting up a secure connection between two Linux systems, reblochon and gouda. We explain different IPsec user-land tools and how to use them to set up a secure connection between two systems. At the end, we present our benchmarks and discuss them.
To use IPsec, you need a kernel that supports IPsec protocols and user-land tools that allow key management and key exchange. These keys are used for different cryptographic algorithms.
For Linux kernels 2.5.47 and higher, IPsec support is a part of the kernel itself. However, this support is not enabled by default. If you have a Linux distribution such as Suse 9.1 or Fedora Core 2, it already comes with a 2.6 kernel and IPsec is enabled by default. If you use some other Linux distribution, for example, Fedora Core 1, you need to install a 2.6.x version of the kernel--the higher the better. This new kernel must be compiled with the following options enabled. Go to Device drivers -> Networking support -> Networking options to enable:
IP: AH transformation
IP: ESP transformation
IP: IPComp transformation
IPsec user configuration interface
You also must include all the cryptographic algorithms you plan to use for your IPsec setup.
On the user-land side, the only thing you need is setkey and Racoon, which are part of the IPsec-tools Project (see Resources). The installation of these tools is straightforward: download the source code and proceed as usual with configure, make and make install commands. There even might be a precompiled package for your distribution of choice.
You can use IPsec in two modes, transport or tunnel. Briefly, transport mode is used to secure host-to-host communications, and tunnel mode is used to tunnel securely site-to-site communications. In transport mode, a special header for ESP and AH is added to the normal IP header. In tunnel mode, the IP packet of transport mode with an ESP and AH header is encapsulated in a normal IP packet. That way, the ESP and AH header is not visible directly to routers that might discard a packet with unknown options.
IPsec can be configured in different ways. Here are three ways to configure an IPsec secure connection between two hosts:
Shared Secret Keys: Start with a shared key on two nodes. Upon initialization of a secure connection between two nodes, this common shared secret is used for specified encryption or authentication algorithms. Using shared keys is the easiest way to configure but it also is less secure, as the shared secret most probably is contained in a configuration or script file on both machines. Also, if you do not change your keys often, it is possible that someone could capture enough packets to be able to retrieve the key.
Pre-Shared Key: In this mode, you need to run Racoon. Its functionality is similar to the shared secret key. The only difference is Racoon uses the pre-shared key as a seed to negotiate a complete key and periodically change that key.
X.509 Certificate: The most secure method to manage keys securely is to use the X.509 certificate. This solution requires access to a trusted certification authority (CA); otherwise, you need to set up your own CA. IPsec configuration in this case is not much more complicated, but interactions with a trusted certificate might be a problem.
In our simple scenario, we are more interested in discussing IPsec implementation performance rather than secure connection issues. So here we discuss the configuration of shared and pre-shared keys only.
|PostgreSQL, the NoSQL Database||Jan 29, 2015|
|HPC Cluster Grant Accepting Applications!||Jan 28, 2015|
|Sharing Admin Privileges for Many Hosts Securely||Jan 28, 2015|
|Red Hat Enterprise Linux 7.1 beta available on IBM Power Platform||Jan 23, 2015|
|Designing with Linux||Jan 22, 2015|
|Wondershaper—QOS in a Pinch||Jan 21, 2015|
- PostgreSQL, the NoSQL Database
- Sharing Admin Privileges for Many Hosts Securely
- HPC Cluster Grant Accepting Applications!
- Internet of Things Blows Away CES, and it May Be Hunting for YOU Next
- Ideal Backups with zbackup
- Wondershaper—QOS in a Pinch
- Designing with Linux
- Red Hat Enterprise Linux 7.1 beta available on IBM Power Platform
- Slow System? iotop Is Your Friend
- January 2015 Issue of Linux Journal: Security
Editorial Advisory Panel
Thank you to our 2014 Editorial Advisors!
- Jeff Parent
- Brad Baillio
- Nick Baronian
- Steve Case
- Chadalavada Kalyana
- Caleb Cullen
- Keir Davis
- Michael Eager
- Nick Faltys
- Dennis Frey
- Philip Jacob
- Jay Kruizenga
- Steve Marquez
- Dave McAllister
- Craig Oda
- Mike Roberts
- Chris Stark
- Patrick Swartz
- David Lynch
- Alicia Gibb
- Thomas Quinlan
- Carson McDonald
- Kristen Shoemaker
- Charnell Luchich
- James Walker
- Victor Gregorio
- Hari Boukis
- Brian Conner
- David Lane