Motion: Your Eye in the Sky for Computer Room Surveillance
Let's say you have a room full of thousands of dollars' worth of computer equipment. That's probably something you want to keep an eye on, right? With that in mind, you install a network-connected camera. Now, you can surf over to the camera's Web page and see what's going on in the server room at any time of day or night. That's an improvement, but you quickly realize some sort of recording facility is needed, in case you need to figure out who was in the room last Tuesday. So, you start saving the video to another system on the network for possible viewing at a later time. Maybe you write a few scripts to rotate the video after a week or so to keep from filling up your hard drive.
After wading through hours of video to find out who “borrowed” your favorite screwdriver, you realize further refinements are necessary. Wouldn't it be great if the computer could keep only the interesting video and throw out everything else? Enter Motion, a free motion-detection program. Process your video through it, and 24 hours of daily video becomes 15 minutes of video clips documenting every time something moved in that room—technology to the rescue.
Motion works with either standalone netcams, such as those offered by Axis (see the on-line Resources), or any camera connected to a video4linux-compatible video capture card. I concentrate here on using a standalone camera, the Axis 2100, because it's simpler to set up. In any case, you need a Linux system to save the video and to run Motion as well. Motion can require quite a bit of processing power, but a system with a Pentium III CPU or higher should work okay if the machine is dedicated to running only Motion.
Installation and configuration of the Axis camera is straightforward. Pick a location for it in the room you want to monitor, and run power and Ethernet cables. In my experience, a camera mounted slightly above eye level, seven feet up or so, in a corner of the room provides the best coverage. Follow the camera install instructions to assign it an IP address on your network. Then, verify that the camera works by pointing your Web browser at the camera's Web page.
The computer system that is going to save the video and run Motion can be situated anywhere you like. It's probably best to keep it on the same logical and physical network as the camera, for simplicity's sake.
Any modern Linux distribution should work fine. I use Fedora Core 1 in my setup.
Obtain Motion from the Motion Web site (see Resources). The current version at the time of this writing is 3.1.16. You can use either the RPM supplied on the Motion Web site or build from source. I don't recommend using RPMs or Debian packages from elsewhere as they tend to be out of date and lacking features. Numerous important changes have occurred in Motion development in a few months' time.
The only other software dependency is the ffmpeg library, which Motion uses to generate MPEG videos. You must use the released version 0.4.8 of ffmpeg, as newer development versions do not work well with Motion. Download ffmpeg source (see Resources); you must have ffmpeg built and installed before building Motion. Otherwise, Motion attempts to use an older tool called mpegplayer to create videos. You probably don't have that installed either, so Motion won't work very well.
After you have downloaded both Motion and ffmpeg, untar them in a directory such as /tmp. Then, cd to the ffmpeg source directory and run:
$ ./configure $ make # make install
The last command must be run as root.
These commands install the ffmpeg libraries under /usr/local/lib. Then, cd to the Motion source directory and again run ./configure. This time, make sure to check the results. In particular, under Configure Status, FFmpeg Support must say Yes. If not, Motion didn't find the ffmpeg library on your system. This is the number one cause of problems and confusion when installing Motion. Don't continue until you resolve this problem. Figure out where on your system the file libavcodec-0.4.8.so is located, and rerun configure in the Motion directory as follows:
$ ./configure --with-ffmpeg=/some/random/path
Once you are able to run configure and see it report FFmpeg Support: Yes, you can build and install motion:
$ make # make install
|PostgreSQL, the NoSQL Database||Jan 29, 2015|
|HPC Cluster Grant Accepting Applications!||Jan 28, 2015|
|Sharing Admin Privileges for Many Hosts Securely||Jan 28, 2015|
|Red Hat Enterprise Linux 7.1 beta available on IBM Power Platform||Jan 23, 2015|
|Designing with Linux||Jan 22, 2015|
|Wondershaper—QOS in a Pinch||Jan 21, 2015|
- PostgreSQL, the NoSQL Database
- Sharing Admin Privileges for Many Hosts Securely
- HPC Cluster Grant Accepting Applications!
- Internet of Things Blows Away CES, and it May Be Hunting for YOU Next
- Wondershaper—QOS in a Pinch
- Designing with Linux
- Ideal Backups with zbackup
- January 2015 Issue of Linux Journal: Security
- Slow System? iotop Is Your Friend
- Non-Linux FOSS: Animation Made Easy
Editorial Advisory Panel
Thank you to our 2014 Editorial Advisors!
- Jeff Parent
- Brad Baillio
- Nick Baronian
- Steve Case
- Chadalavada Kalyana
- Caleb Cullen
- Keir Davis
- Michael Eager
- Nick Faltys
- Dennis Frey
- Philip Jacob
- Jay Kruizenga
- Steve Marquez
- Dave McAllister
- Craig Oda
- Mike Roberts
- Chris Stark
- Patrick Swartz
- David Lynch
- Alicia Gibb
- Thomas Quinlan
- Carson McDonald
- Kristen Shoemaker
- Charnell Luchich
- James Walker
- Victor Gregorio
- Hari Boukis
- Brian Conner
- David Lane