Network Buffers and Memory Management
In order for the network protocol la
yers to perform in a sensible manner, the device has to provide a set of capability flags and variables that are also maintained in the device structure.
The mtu is the largest payload that can be sent over this interface, i.e., the largest packet size not including any bottom layer headers that the device itself will provide. This number is used by the protocol layers such as IP to select suitable packet sizes to send. There are minimums imposed by each protocol. A device is not usable for IPX without a 576 byte frame size or higher. IP needs at least 72 bytes and does not perform sensibly below about 200 bytes. It is up to the protocol layers to decide whether to co-operate with your device.
The family is always set to AF_INET and indicates the protocol family the device is using. Linux allows a device to be using multiple protocol families at once, and maintains this information solely to look more like the standard BSD networking API.
The interface hardware type field is taken from a table of physical media types. The values used by the ARP protocol (see RFC1700) are used by those media that support ARP, and additional values are assigned for other physical layers. New values are added whenever necessary both to the kernel and to net-tools, the package containing programs like ifconfig that need to be able to decode this field. The fields defined as of Linux pre2.0.5 are:
From RFC1700: ARPHRD_NETROM NET/ROM™ devices ARPHRD_ETHER 10 and 100Mbit/second Ethernet ARPHRD_EETHER Experimental Ethernet (not used) ARPHRD_AX25 AX.25 level 2 interfaces ARPHRD_PRONET PROnet token ring (not used) ARPHRD_CHAOS ChaosNET (not used) ARPHRD_IEE802 802.2 networks notably token ring ARPHRD_ARCNET ARCnet interfaces ARPHRD_DLCI Frame Relay DLCI Defined by Linux: ARPHRD_SLIP Serial Line IP protocol ARPHRD_CSLIP SLIP with VJ header compression ARPHRD_SLIP6 6bit encoded SLIP ARPHRD_CSLIP6 6bit encoded header compressed SLIP ARPHRD_ADAPT SLIP interface in adaptive mode ARPHRD_PPP PPP interfaces (async and sync) ARPHRD_TUNNEL IPIP tunnels ARPHRD_TUNNEL6 IPv6 over IP tunnels ARPHRD_FRAD Frame Relay Access Device ARPHRD_SKIP SKIP encryption tunnel ARPHRD_LOOPBACK Loopback device ARPHRD_LOCALTLK Localtalk apple networking device ARPHRD_METRICOM Metricom Radio Network
Those interfaces marked unused are defined types but without any current support on the existing net-tools. The Linux kernel provides additional generic support routines for devices using Ethernet and token ring.
The pa_addr field is used to hold the IP address when the interface is up. Interfaces should start down with this variable clear. pa_brdaddr is used to hold the configured broadcast address, pa_dstaddr is the target of a point to point link, and pa_mask is the IP netmask of the interface. All of these can be initialized to zero. The pa_alen field holds the length of an address (in our case an IP address), and should be initialized to 4.
The hard_header_len is the number of bytes the device needs at the start of a network buffer passed to it. This value does not have to equal the number of bytes of physical header that will be added, although this number is usually used. A device can use this value to provide itself with a scratch pad at the start of each buffer.
In the 1.2.x series kernels, the skb->data pointer will point to the buffer start, and you must avoid sending your scratch pad. This also means that for devices with variable length headers you need to allocate max_size+1 bytes and keep a length byte at the start so that you know where the header actually begins (the header should be contiguous with the data). Linux 1.3.x makes life much simpler. It ensures that you have at least as much room as you requested, free at the start of the buffer. It is up to you to use skb_push() appropriately, as we discussed in the section on networking buffers.
The physical media addresses (if any) are maintained in dev_addr and broadcast respectively and are byte arrays. Addresses smaller than the size of the array are stored starting from the left. The addr_len field is used to hold the length of a hardware address. With many media there is no hardware address, and in this case, this field should be set to zero. For some other interfaces, the address must be set by a user program. The ifconfig tool permits the setting of an interface hardware address. In this case it need not be set initially, but the open code should take care not to allow a device to start transmitting before an address has been set.
|Free Today: September Issue of Linux Journal (Retail value: $5.99)||Sep 27, 2016|
|nginx||Sep 27, 2016|
|Epiq Solutions' Sidekiq M.2||Sep 26, 2016|
|Nativ Disc||Sep 23, 2016|
|Android Browser Security--What You Haven't Been Told||Sep 22, 2016|
|The Many Paths to a Solution||Sep 21, 2016|
- Android Browser Security--What You Haven't Been Told
- Free Today: September Issue of Linux Journal (Retail value: $5.99)
- Readers' Choice Awards 2013
- Epiq Solutions' Sidekiq M.2
- Nativ Disc
- The Many Paths to a Solution
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- Synopsys' Coverity
- Returning Values from Bash Functions
Pick up any e-commerce web or mobile app today, and you’ll be holding a mashup of interconnected applications and services from a variety of different providers. For instance, when you connect to Amazon’s e-commerce app, cookies, tags and pixels that are monitored by solutions like Exact Target, BazaarVoice, Bing, Shopzilla, Liveramp and Google Tag Manager track every action you take. You’re presented with special offers and coupons based on your viewing and buying patterns. If you find something you want for your birthday, a third party manages your wish list, which you can share through multiple social- media outlets or email to a friend. When you select something to buy, you find yourself presented with similar items as kind suggestions. And when you finally check out, you’re offered the ability to pay with promo codes, gifts cards, PayPal or a variety of credit cards.Get the Guide