Linux Swap Space
which gathers data over a four-minute time span every five minutes. You can analyze the resulting data using a utility called kSar (ksar.atomique.net) or at the command line. kSar has the advantage of making graphs that compare one metric to another.
You can check your historical usage by running sar against one of these data collection files. For example, to view data from the 2nd of this month:
# sar -f /var/log/sa/sa02
The most direct measure of swapping is reported from sar -W:
# sar -W -f /var/log/sa/sa02 00:00:01 pswpin/s pswpout/s 00:10:01 0.00 0.00 ...
The raw page numbers are a good start. If nonzero, you're doing some swapping. How much is acceptable is more difficult to judge. You'll need to examine the I/O on your swap partition. To do this, you may need to figure out the device major/minor numbers of your swap device. For example, if you swap to /dev/sdb1, use:
# ls -l /dev/hdb1 brw-r----- 1 root disk 8, 17 Dec 1 14:24 /dev/sdb1
to find that your device numbers are 8/17. Many versions of sar will report disk I/O by major/minor number. The command to look at the gathered disk data is:
# sar -d -f /var/log/sa/sa02 23:15:01 DEV \ tps rd_sec/s \ wr_sec/s avgrq-sz avgqu-sz \ await svctm %util 23:15:01 dev8-17 \ 0.00 0.00 \ 0.00 0.00 0.00 \ 0.00 0.00 0.00
If you have a lot of disks, use egrep to see only the header and device:
# sar -d -f /var/log/sa/sa02 | egrep '(DEV|dev8-17)' ...
Any swapping could be bad, but if you're seeing the avgrq-sz (average size in sectors of the requests that were issued to the device) below 1 and an await time that roughly matches svctm (average service time in milliseconds for I/O requests that were issued to the device), you may be okay. Check other indicators of system performance, such as CPU waiting for I/O and high system CPU times.
Figures 2 and 3 show some custom graphs generated with kSar that make it easy to see things more clearly.
Figure 2 is a graph comparing the amount of swap space used to the amount of time the CPU spent waiting on I/O. There are spikes of I/O wait, but they don't follow any sort of pattern with the swap use. However, this system deserves more attention because there is an I/O bottleneck of some sort. It is likely that this system is underperforming, but it probably is not a swapping issue (in this case, the I/O waits were heavy database request loads).
Figure 3 shows a graph comparing writes to the swap device vs. I/O wait (over a daytime time interval). It is a bit hard to see, but the red line for I/O is actually zero across the whole of the time span. This indicates that the I/O wait had nothing to do with swapping. Note that this does not mean no swapping of any sort occurred. Non-anonymous pages could have been reclaimed and reloaded.
If you are lucky enough to have all of your data on one partition and all of your code on another, you can analyze this sort of paging by watching the reads on your “code” partition. The reads will indicate program loading at startup (which may be infrequent on your systems) and also paging due to memory pressure. If the reads correspond to large I/O waits, you may benefit from more RAM.
The final parameter I want to talk about can affect the responsiveness of certain loads. Have you ever left your system idle for a few hours, only to return to find that it takes a long time to start responding again? Here is probably what is happening: while you were gone, a cron job (like updatedb) scanned the filesystem, and because you weren't using the computer, all of the code pages for your “inactive” programs were thrown out in favor of disk cache! There is a kernel parameter called vm.swappiness that will affect the tendency of the system to throw out code pages instead of others.
The default value of vm.swappiness is 60 on most systems. Changing this parameter to 0 will prevent the kernel from throwing out code pages for filesystem caching and will prevent your desktop from becoming zombie-like due to an unmonitored filesystem scan.
The default value is fine for production systems, because any services that are heavily used will be kept in memory due to their activity. This allows the file cache to expand over anything that is truly unused and generally will work better. It may be advantageous to tune this if you are pretty certain that the majority of memory for programs should be kept (for example, you run a database that does most of its own caching). It might also help to increase this parameter to 100 on systems that have a set of very active programs.
As with any performance parameter, it helps to have some benchmarks that simulate your real workload so you can measure the effects.
Tuning these parameters will lead to a virtual memory system that provides a more stable foundation, particularly for production systems running programs that consume large amounts of memory.
Tony Kay has been working with UNIX and Linux systems for more than 20 years. He lives in Bend, Oregon, where he manages large Linux systems and develops mobile applications.
Webinar: 8 Signs You’re Beyond Cron
On Demand NOW
Join Linux Journal and Pat Cameron, Director of Automation Technology at HelpSystems, as they discuss the eight primary advantages of moving beyond cron job scheduling. In this webinar, you’ll learn about integrating cron with an enterprise scheduler.View Now!
|Dr Hjkl on the Command Line||May 21, 2015|
|Initializing and Managing Services in Linux: Past, Present and Future||May 20, 2015|
|Goodbye, Pi. Hello, C.H.I.P.||May 18, 2015|
|Enter to Win Archive DVD + Free Backup Solution||May 18, 2015|
|Using Hiera with Puppet||May 14, 2015|
|Urgent Kernel Patch for Ubuntu||May 12, 2015|
- Initializing and Managing Services in Linux: Past, Present and Future
- Dr Hjkl on the Command Line
- Goodbye, Pi. Hello, C.H.I.P.
- Using Hiera with Puppet
- Gartner Dubs DivvyCloud Cool Cloud Management Vendor
- Mumblehard--Let's End Its Five-Year Reign
- Enter to Win Archive DVD + Free Backup Solution
- Infinite BusyBox with systemd
- It's Easier to Ask Forgiveness...
- A More Stable Future for Ubuntu