Monitoring Hard Disks with SMART
Listing 4. Output of smartctl -l error /dev/hda
SMART Error Log Version: 1 No Errors Logged
The final part of the smartctl output (Listing 5) is a report of the self-tests run on the disk. These show two types of self-tests, short and long. (ATA-6/7 disks also may have conveyance and selective self-tests.) These can be run with the commands smartctl -t short /dev/hda and smartctl -t long /dev/hda and do not corrupt data on the disk. Typically, short tests take only a minute or two to complete, and long tests take about an hour. These self-tests do not interfere with the normal functioning of the disk, so the commands may be used for mounted disks on a running system. On our computing cluster nodes, a long self-test is run with a cron job early every Sunday morning. The entries in Listing 5 all are self-tests that completed without errors; the LifeTime column shows the power-on age of the disk when the self-test was run. If a self-test finds an error, the Logical Block Address (LBA) shows where the error occurred on the disk. The Remaining column shows the percentage of the self-test remaining when the error was found. If you suspect that something is wrong with a disk, I strongly recommend running a long self-test to look for problems.
Listing 5. Output of smartctl -l selftest /dev/hda
SMART Self-test log, version number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended off-line Completed 00% 3525 - # 2 Extended off-line Completed 00% 3357 - # 3 Short off-line Completed 00% 3059 -
The smartctl -t offline command can be used to carry out off-line tests. These off-line tests do not make entries in the self-test log. They date back to the SFF-8035i standard, and update values of the Attributes that are not updated automatically under normal disk operation (see the UPDATED column in Listing 3). Some disks support automatic off-line testing, enabled by smartctl -o on, which automatically runs an off-line test every few hours.
The SMART standard provides a mechanism for running disk self-tests and for monitoring aspects of disk performance. Its main shortcoming is that it doesn't provide a direct mechanism for informing the OS or user if problems are found. In fact, because disk SMART status frequently is not monitored, many disk problems go undetected until they lead to catastrophic failure. Of course, you can monitor disks on a regular basis using the smartctl utility, as I've described, but this is a nuisance.
The remaining part of the smartmontools package is the smartd dæmon that does regular monitoring for you. It monitors the disk's SMART data for signs of problems. It can be configured to send e-mail to users or system administrators or to run arbitrary scripts if problems are detected. By default, when smartd is started, it registers the system's disks. It then checks their status every 30 minutes for failing Attributes, failing health status or increased numbers of ATA errors or failed self-tests and logs this information with SYSLOG in /var/log/messages by default.
You can control and fine-tune the behavior of smartd using the configuration file /etc/smartd.conf. This file is read when smartd starts up, before it forks into the background. Each line contains Directives pertaining to a different disk. The configuration file on our computing cluster nodes look like this:
# /etc/smartd.conf config file /dev/hda -S on -o on -a -I 194 -m firstname.lastname@example.org /dev/hdc -S on -o on -a -I 194 -m email@example.com
The first column indicates the device to be monitored. The -o on Directive enables the automatic off-line testing, and the -S on Directive enables automatic Attribute autosave. The -m Directive is followed by an e-mail address to which warning messages are sent, and the -a Directive instructs smartd to monitor all SMART features of the disk. In this configuration, smartd logs changes in all normalized attribute values. The -I 194 Directive means ignore changes in Attribute #194, because disk temperatures change often, and it's annoying to have such changes logged on a regular basis.
Normally smartd is started by the normal UNIX init mechanism. For example, on Red Hat distributions, /etc/rc.d/init.d/smartd start and /etc/rc.d/init.d/smartd stop can be used to start and stop the dæmon.
Further information about the smartd and its config file can be found in the man page (man smartd), and summaries can be found with the commands smartd -D and smartd -h. For example, the -M test Directive sends a test e-mail warning message to confirm that warning e-mail messages are delivered correctly. Other Directives provide additional flexibility, such as monitoring changes in raw Attribute values.
What should you do if a disk shows signs of problems? What if a disk self-test fails or the disk's SMART health status fails? Start by getting your data off the disk and on to another system as soon as possible. Second, run some extended disk self-tests and see if the problem is repeatable at the same LBA. If so, something probably is wrong with the disk. If the disk has failing SMART health status and is under warranty, the vendor usually will replace it. If the disk is failing its self-tests, many manufacturers provide specialized disk health programs, for example, Maxtor's PowerMax or IBM's Drive Fitness Test. Sometimes these programs actually can repair a disk by remapping bad sectors. Often, they report a special error code that can be used to get a replacement disk.
This article has covered the basics of smartmontools. To learn more, read the man pages and Web page, and then write to the support mailing list if you need further help. Remember, smartmontools is no substitute for backing up your data. SMART cannot and does not predict all disk failures, but it often provides clues that something is amiss and has helped to keep many computing clusters operating reliably.
Several developers are porting smartmontools to FreeBSD, Darwin and Solaris, and we recently have added extensions to allow smartmontools to monitor and control the ATA disks behind 3ware RAID controllers. If you would like to contribute to the development of smartmontools, write to the support mailing list. We especially are interested in information about the interpretation and meaning of vendor-specific SMART Attribute and raw values.
Bruce Allen is a professor of Physics at the University of Wisconsin - Milwaukee. He does research work on gravitational waves and the very early universe, and he has built several large Linux clusters for data analysis use.
- Goldtouch Semi-Vertical Mouse
- My Childhood in a Cigar Box
- Let's Go to Mars with Martian Lander
- Applied Expert Systems, Inc.'s CleverView for TCP/IP on Linux
- Papa's Got a Brand New NAS
- VMware's Clarity Design System
- Panther MPC, Inc.'s Panther Alpha
- Linux Journal January 2017
- Simplenote, Simply Awesome!
Pick up any e-commerce web or mobile app today, and you’ll be holding a mashup of interconnected applications and services from a variety of different providers. For instance, when you connect to Amazon’s e-commerce app, cookies, tags and pixels that are monitored by solutions like Exact Target, BazaarVoice, Bing, Shopzilla, Liveramp and Google Tag Manager track every action you take. You’re presented with special offers and coupons based on your viewing and buying patterns. If you find something you want for your birthday, a third party manages your wish list, which you can share through multiple social- media outlets or email to a friend. When you select something to buy, you find yourself presented with similar items as kind suggestions. And when you finally check out, you’re offered the ability to pay with promo codes, gifts cards, PayPal or a variety of credit cards.Get the Guide