Creating VPNs with IPsec and SSL/TLS
OpenVPN is an open-source project founded by James Yonan. It provides a VPN solution based on SSL/TLS. Transport Layer Security (TLS) and its predecessor, Secure Sockets Layer (SSL), are cryptographic protocols that provide secure communications data transfer on the Internet. SSL has been in existence since the early '90s.
The OpenVPN networking model is based on TUN/TAP virtual devices; TUN/TAP is part of the Linux kernel. The first TUN driver in Linux was developed by Maxim Krasnyansky.
OpenVPN installation and configuration is simpler in comparison with IPsec. OpenVPN supports RSA authentication, Diffie-Hellman key agreement, HMAC-SHA1 integrity checks and more. When running in server mode, it supports multiple clients (up tp 128) to connect to a VPN server over the same port. You can set up your own Certificate Authority (CA) and generate certificates and keys for an OpenVPN server and multiple clients.
OpenVPN operates in user-space mode; this makes it easy to port OpenVPN to other operating systems.
First, download and install the ipsec-tools package and the Openswan package (most distros have these packages).
The VPN tunnel has two participants on its ends, called left and right, and which participant is considered left or right is arbitrary. You have to configure various parameters for these two ends in /etc/ipsec.conf (see man 5 ipsec.conf). The /etc/ipsec.conf file is divided into sections. The conn section contains a connection specification, defining a network connection to be made using IPsec.
An example of a conn section in /etc/ipsec.conf, which defines a tunnel between two nodes on the same LAN, with the left one as 192.168.0.89 and the right one as 192.168.0.92, is as follows:
... conn linux-to-linux # # Simply use raw RSA keys # After starting openswan, run: # ipsec showhostkey --left (or --right) # and fill in the connection similarly # to the example below. left=192.168.0.89 leftrsasigkey=0sAQPP... # The remote user. # right=192.168.0.92 rightrsasigkey=0sAQON... type=tunnel auto=start ...
You can generate the leftrsasigkey and rightrsasigkey on both participants by running:
ipsec rsasigkey --verbose 2048 > rsa.key
Then, copy and paste the contents of rsa.key into /etc/ipsec.secrets.
In some cases, IPsec clients are roaming clients (with a random IP address). This happens typically when the client is a laptop used from remote locations (such clients are called Roadwarriors). In this case, use the following in ipsec.conf:
The %any keyword is used to specify an unknown IP address.
The type parameter of the connection in this example is tunnel (which is the default). Other types can be transport, signifying host-to-host transport mode; passthrough, signifying that no IPsec processing should be done at all; drop, signifying that packets should be discarded; and reject, signifying that packets should be discarded and a diagnostic ICMP should be returned.
The auto parameter of the connection tells which operation should be done automatically at IPsec startup. For example, auto=start tells it to load and initiate the connection; whereas auto=ignore (which is the default) signifies no automatic startup operation. Other values for the auto parameter can be add, manual or route.
After configuring /etc/ipsec.conf, start the service with:
service ipsec start
You can perform a series of checks to get info about IPsec on your machine by typing ipsec verify. And, output of ipsec verify might look like this:
Checking your system to see if IPsec has installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.4.7/K2.6.21-rc7 (netkey) Checking for IPsec support in kernel [OK] NETKEY detected, testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking for RSA private key (/etc/ipsec.d/hostkey.secrets) [OK] Checking that pluto is running [OK] Checking for 'ip' command [OK] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED]
You can get information about the tunnel you created by running:
ipsec auto --status
You also can view various low-level IPSec messages in the kernel syslog.
You can test and verify that the packets flowing between the two participants are indeed esp frames by opening an FTP connection (for example), between the two participants and running:
tcpdump -f esp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes
You should see something like this:
IP 192.168.0.92 > 192.168.0.89: ESP(spi=0xd514eed9,seq=0x7) IP 192.168.0.89 > 192.168.0.92: ESP(spi=0x3a1563b9,seq=0x6) IP 192.168.0.89 > 192.168.0.92: ESP(spi=0x3a1563b9,seq=0x7) IP 192.168.0.92 > 192.168.0.89: ESP(spi=0xd514eed9,seq=0x8)
Note that the spi (Security Parameter Index) header is the same for all packets; this is an identifier of the connection.
If you need to support NAT traversal, add nat_traversal=yes in ipsec.conf; nat_traversal=no is the default.
The Linux IPsec stack can work with pluto from Openswan, racoon from the KAME Project (which is included in ipsec-tools) or isakmpd from OpenBSD.
Practical Task Scheduling Deployment
July 20, 2016 12:00 pm CDT
One of the best things about the UNIX environment (aside from being stable and efficient) is the vast array of software tools available to help you do your job. Traditionally, a UNIX tool does only one thing, but does that one thing very well. For example, grep is very easy to use and can search vast amounts of data quickly. The find tool can find a particular file or files based on all kinds of criteria. It's pretty easy to string these tools together to build even more powerful tools, such as a tool that finds all of the .log files in the /home directory and searches each one for a particular entry. This erector-set mentality allows UNIX system administrators to seem to always have the right tool for the job.
Cron traditionally has been considered another such a tool for job scheduling, but is it enough? This webinar considers that very question. The first part builds on a previous Geek Guide, Beyond Cron, and briefly describes how to know when it might be time to consider upgrading your job scheduling infrastructure. The second part presents an actual planning and implementation framework.
Join Linux Journal's Mike Diehl and Pat Cameron of Help Systems.
Free to Linux Journal readers.Register Now!
- SUSE LLC's SUSE Manager
- My +1 Sword of Productivity
- Murat Yener and Onur Dundar's Expert Android Studio (Wrox)
- Managing Linux Using Puppet
- Non-Linux FOSS: Caffeine!
- Doing for User Space What We Did for Kernel Space
- SuperTuxKart 0.9.2 Released
- Parsing an RSS News Feed with a Bash Script
- Google's SwiftShader Released
- SourceClear Open
With all the industry talk about the benefits of Linux on Power and all the performance advantages offered by its open architecture, you may be considering a move in that direction. If you are thinking about analytics, big data and cloud computing, you would be right to evaluate Power. The idea of using commodity x86 hardware and replacing it every three years is an outdated cost model. It doesn’t consider the total cost of ownership, and it doesn’t consider the advantage of real processing power, high-availability and multithreading like a demon.
This ebook takes a look at some of the practical applications of the Linux on Power platform and ways you might bring all the performance power of this open architecture to bear for your organization. There are no smoke and mirrors here—just hard, cold, empirical evidence provided by independent sources. I also consider some innovative ways Linux on Power will be used in the future.Get the Guide