Monitoring Virtual Memory with vmstat
Linux novices often find virtual memory mysterious, but with a grasp of the fundamental concepts, it's easy to understand. With this knowledge, you can monitor your system's memory utilization using vmstat and detect problems that can adversely affect system performance.
Physical memory—the actual RAM installed—is a finite resource on any system. The Linux memory handler manages the allocation of that limited resource by freeing portions of physical memory when possible.
All processes use memory, of course, but each process doesn't need all its allocated memory all the time. Taking advantage of this fact, the kernel frees up physical memory by writing some or all of a process' memory to disk until it's needed again.
The kernel uses paging and swapping to perform this memory management. Paging refers to writing portions, termed pages, of a process' memory to disk. Swapping, strictly speaking, refers to writing the entire process, not just part, to disk. In Linux, true swapping is exceedingly rare, but the terms paging and swapping often are used interchangeably.
When pages are written to disk, the event is called a page-out, and when pages are returned to physical memory, the event is called a page-in. A page fault occurs when the kernel needs a page, finds it doesn't exist in physical memory because it has been paged-out, and re-reads it in from disk.
Page-ins are common, normal and are not a cause for concern. For example, when an application first starts up, its executable image and data are paged-in. This is normal behavior.
Page-outs, however, can be a sign of trouble. When the kernel detects that memory is running low, it attempts to free up memory by paging out. Though this may happen briefly from time to time, if page-outs are plentiful and constant, the kernel can reach a point where it's actually spending more time managing paging activity than running the applications, and system performance suffers. This woeful state is referred to as thrashing.
Using swap space is not inherently bad. Rather, it's intense paging activity that's problematic. For instance, if your most-memory-intensive application is idle, it's fine for portions of it to be set aside when another large job is active. Memory pages belonging to an idle application are better set aside so the kernel can use physical memory for disk buffering.
vmstat, as its name suggests, reports virtual memory statistics. It shows how much virtual memory there is, how much is free and paging activity. Most important, you can observe page-ins and page-outs as they happen. This is extremely useful.
To monitor the virtual memory activity on your system, it's best to use vmstat with a delay. A delay is the number of seconds between updates. If you don't supply a delay, vmstat reports the averages since the last boot and quit. Five seconds is the recommended delay interval.
To run vmstat with a five-second delay, type:
You also can specify a count, which indicates how many updates you want to see before vmstat quits. If you don't specify a count, the count defaults to infinity, but you can stop output with Ctrl-C.
To run vmstat with ten updates, five seconds apart, type:
vmstat 5 10
Here's an example of a system free of paging activity:
procs memory swap io system cpu r b w swpd free buff cache si so bi bo in cs us sy id 0 0 0 29232 116972 4524 244900 0 0 0 0 0 0 0 0 0 0 0 0 29232 116972 4524 244900 0 0 0 0 2560 6 0 1 99 0 0 0 29232 116972 4524 244900 0 0 0 0 2574 10 0 2 98
All fields are explained in the vmstat man page, but the most important columns for this article are free, si and so. The free column shows the amount of free memory, si shows page-ins and so shows page-outs. In this example, the so column is zero consistently, indicating there are no page-outs.
The abbreviations so and si are used instead of the more accurate po and pi for historical reasons.
Here's an example of a system with paging activity:
procs memory swap io system cpu r b w swpd free buff cache si so bi bo in cs us sy id . . . 1 0 0 13344 1444 1308 19692 0 168 129 42 1505 713 20 11 69 1 0 0 13856 1640 1308 18524 64 516 379 129 4341 646 24 34 42 3 0 0 13856 1084 1308 18316 56 64 14 0 320 1022 84 9 8
Notice the nonzero so values indicating there is not enough physical memory and the kernel is paging out. You can use top and ps to identify the processes that are using the most memory.
You also can use top to show memory and swap statistics. Here is an example of the uppermost portion of a typical top report:
14:23:19 up 348 days, 3:02, 1 user, load average: 0.00, 0.00, 0.00 55 processes: 54 sleeping, 1 running, 0 zombie, 0 stopped CPU states: 0.0% user, 2.4% system, 0.0% nice, 97.6% idle Mem: 481076K total, 367508K used, 113568K free, 4712K buffers Swap: 1004052K total, 29852K used, 974200K free, 244396K cached
For more information about top, see the top man page.
Fast/Flexible Linux OS Recovery
On Demand Now
In this live one-hour webinar, learn how to enhance your existing backup strategies for complete disaster recovery preparedness using Storix System Backup Administrator (SBAdmin), a highly flexible full-system recovery solution for UNIX and Linux systems.
Join Linux Journal's Shawn Powers and David Huffman, President/CEO, Storix, Inc.
Free to Linux Journal readers.Register Now!
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- ServersCheck's Thermal Imaging Camera Sensor
- The Italian Army Switches to LibreOffice
- Linux Mint 18
- Petros Koutoupis' RapidDisk
- Oracle vs. Google: Round 2
- The FBI and the Mozilla Foundation Lock Horns over Known Security Hole
- Privacy and the New Math
- Ben Rady's Serverless Single Page Apps (The Pragmatic Programmers)
Until recently, IBM’s Power Platform was looked upon as being the system that hosted IBM’s flavor of UNIX and proprietary operating system called IBM i. These servers often are found in medium-size businesses running ERP, CRM and financials for on-premise customers. By enabling the Power platform to run the Linux OS, IBM now has positioned Power to be the platform of choice for those already running Linux that are facing scalability issues, especially customers looking at analytics, big data or cloud computing.
￼Running Linux on IBM’s Power hardware offers some obvious benefits, including improved processing speed and memory bandwidth, inherent security, and simpler deployment and management. But if you look beyond the impressive architecture, you’ll also find an open ecosystem that has given rise to a strong, innovative community, as well as an inventory of system and network management applications that really help leverage the benefits offered by running Linux on Power.Get the Guide