Kernel Korner - ATA Over Ethernet: Putting Hard Drives on the LAN
The following example is based on a true story. Stan is a fictional sysadmin working for the state government. New state legislation requires that all official documents be archived permanently. Any state resident can demand to see any official document at any time. Stan therefore needs a huge storage capacity that can grow without bounds. The performance of the storage needn't be any better than a local ATA disk, though. He wants all of the data to be retrievable easily and immediately.
Stan is comfortable with Ethernet networking and Linux system administration, so he decides to try ATA over Ethernet. He buys some equipment, paying a bit less than $6,500 US for all of the following:
One dual-port gigabit Ethernet card to replace the old 100Mb card in his server.
One 26-port network switch with two gigabit ports.
One Coraid EtherDrive shelf and ten EtherDrive blades.
Ten 400GB ATA drives.
The shelf of ten blades takes up three rack units. Each EtherDrive blade is a small computer that performs the AoE protocol to effectively put one ATA disk on the LAN. Striping data over the ten blades in the shelf results in about the throughput of a local ATA drive, so the gigabit link helps to use the throughput effectively. Although he could have put the EtherDrive blades on the same network as everyone else, he has decided to put the storage on its own network, connected to the server's second network interface, eth1, for security and performance.
Stan reads the Linux Software RAID HOWTO (see the on-line Resources) and decides to use a RAID 10—striping over mirrored pairs—configuration. Although this configuration doesn't result in as much usable capacity as a RAID 5 configuration, RAID 10 maximizes reliability, minimizes the CPU cost of performing RAID and has a shorter array re-initialization time if one disk should fail.
After reading the LVM HOWTO (see Resources), Stan comes up with a plan to avoid ever running out of disk space. JFS is a filesystem that can grow dynamically to large sizes, so he is going to put a JFS filesystem on a logical volume. The logical volume resides, for now, on only one physical volume. That physical volume is the RAID 10 block device. The RAID 10 is created from the EtherDrive storage blades in the Coraid shelf using Linux software RAID. Later, he can buy another full shelf, create another RAID 10, make it into a physical volume and use the new physical volume to extend the logical volume where his JFS lives.
Listing 1 shows the commands Stan uses to prepare his server for doing ATA over Ethernet. He builds the AoE driver with AOE_PARTITIONS=1, because he's using a Debian sarge system running a 2.6 kernel. Sarge doesn't support large minor device numbers yet (see the Minor Numbers sidebar), so he turns off disk partitioning support in order to be able to use more disks. Also, because of Debian bug 292070, Stan installs the latest device mapper and LVM2 userland software.
Listing 1. The first step in building a software RAID device from several AoE drives is setting up AoE.
# setting up the host for AoE # build and install the AoE driver tar xvfz aoe-2.6-5.tar.gz cd aoe-2.6-5 make AOE_PARTITIONS=1 install # AoE needs no IP addresses! :) ifconfig eth1 up # let the network interface come up sleep 5 # load the ATA over Ethernet driver modprobe aoe # see what aoe disks are available aoe-stat
Minor Device Numbers
A program that wants to use a device typically does so by opening a special file corresponding to that device. A familiar example is the /dev/hda file. An ls -l command shows two numbers for /dev/hda, 3 and 0. The major number is 3 and the minor number is 0. The /dev/hda1 file has a minor number of 1, and the major number is still 3.
Until kernel 2.6, the minor number was eight bits in size, limiting the possible minor numbers to 0 through 255. Nobody had that many devices, so the limitation didn't matter. Now that disks have been decoupled from servers, it does matter, and kernel 2.6 uses 20 bits for the minor device number.
Having 1,048,576 values for the minor number is a big help to systems that use many devices, but not all software has caught up. If glibc or a specific application still thinks of minor numbers as eight bits in size, you are going to have trouble using minor device numbers over 255.
To help during this transitional period, the AoE driver may be compiled without support for partitions. That way, instead of there being 16 minor numbers per disk, there's only one per disk. So even on systems that haven't caught up to the large minor device numbers of 2.6, you still can use up to 256 AoE disks.
The commands for creating the filesystem and its logical volume are shown in Listing 2. Stan decides to name the volume group ben and the logical volume franklin. LVM2 now needs a couple of tweaks made to its configuration. For one, it needs a line with types = [ "aoe", 16 ] so that LVM recognizes AoE disks. Next, it needs md_component_detection = 1, so the disks inside RAID 10 are ignored when the whole RAID 10 becomes a physical volume.
|Natalie Rusk's Scratch Coding Cards (No Starch Press)||Feb 17, 2017|
|Own Your DNS Data||Feb 16, 2017|
|IGEL Universal Desktop Converter||Feb 15, 2017|
|Simple Server Hardening||Feb 14, 2017|
|Server Technology's HDOT Alt-Phase Switched POPS PDU||Feb 13, 2017|
|Bash Shell Script: Building a Better March Madness Bracket||Feb 09, 2017|
- Own Your DNS Data
- Simple Server Hardening
- Understanding Firewalld in Multi-Zone Configurations
- Teradici's Cloud Access Platform: "Plug & Play" Cloud for the Enterprise
- From vs. to + for Microsoft and Linux
- The Weather Outside Is Frightful (Or Is It?)
- IGEL Universal Desktop Converter
- Bash Shell Script: Building a Better March Madness Bracket
- Natalie Rusk's Scratch Coding Cards (No Starch Press)
- Server Technology's HDOT Alt-Phase Switched POPS PDU