An Introduction to Embedded Linux Development, Part 2
In Part 1 of this series, we indicated that we would use, as our SBC, the LBox with uClinux from Engineering Technologies Canada Ltd.. Recall that it features the Motorola Coldfire MCF5272 processor, Flash memory, a serial port, a fiber port and up to three 10/100 Ethernet ports. It's ready to go without needing to be built into something else--simply power it up with any suitable power supply in the 5-12 volt range. Although we are using a specific SBC for this project, the activities we undertake here correspond to similar activities on any typical SBC. That said, significant specific differences exist at the more detailed level from one SBC to another.
I purchased about 12 of these systems for our computer science department. If not purchased in quantity, the basic board goes for about $250. Then, you add whatever else you need.
Following along with this series while using an actual LBox SBC would be optimal. Nevertheless, I have organized this series of articles so a reader can glean useful information without purchasing the board. Yet another option would be to use some other SBC and parallel our activities.
To avoid putting forth too much nitty gritty detail here, I refer you to information posted in the FAQ section of the Engineering Technologies Web site.
The goals and subsequent sections for the current article are:
Power up the LBox.
Establish serial communication between LBox and workstation, including what to do if your workstation has no serial port.
Connect via Ethernet.
Install the cross compiling tool chains.
Carry out NFS mounting.
Write a program for the LBox and run it.
The last two sections are quite general and apply to most embedded Linux systems.
My particular setup consists of:
the LBox SBC (from Engtech)
a power supply (from Engtech)
a serial header-to-DB9 cable (from Engtech)
a CD with all needed software (from Engtech)
my laptop (the workstation) with Libranet 2.81, updated to the 2.4.27 kernel
a Belkin F5U409 USB-to-DB9 adapter because my laptop has no external RS-232 DB9 port but does have USB ports
I configured the laptop to use the widely available, tried and true Minicom terminal emulator for the serial connection. It comes with most Linux distributions, and for connecting to SBCs with serial ports, Minicom is a common choice. The Belkin F5U409 uses the mct_u232 driver, which is available with the kernel source. It didn't work properly for me with the 2.4.24 kernel, however, hence the update to 2.4.27.
Before applying power, I connected an Ethernet cable and the serial cable. The Ethernet ports provided on the LBox, when populated, have the expected RJ45 female sockets. The serial port header allows connection of the serial header-to-DB9 cable, which I connected to my laptop via the Belkin F5U409. At this point, everything seemed ready, so I applied power by plugging in the power adapter.
I used Minicom on my laptop to establish the serial connection to the LBox. The details can be found in this FAQ. Once Minicom was configured properly, I reset the LBox using the reset button, located near the board edge, kitty corner from the serial port header. Then, the Minicom window on my laptop spewed out the LBox startup messages. These could be useful subsequently, so I pasted them to an editor on the laptop for subsequent printout.
When the startup messages were finished, I was presented with the command prompt. I then investigated the system to determine what's available. For example, examining /bin showed both Busybox and Tinylogin were present. That suggested a small project to update Busybox to the recent 1.0 version, which has incorporated the Tinylogin functionality. Other things worth noting:
the result from uname -a was
uClinux lbox 2.4.20-uc0 #176 Mon Aug 16 11:25:42 ADT 2004 m68knommu unknown
the result from df was
Filesystem 1k-blocks Used Available Use% Mounted on rootfs 1113 1113 0 100% / /dev/root 1113 1113 0 100% / /dev/ram1 115 7 108 6% /var /dev/mtdblock3 3008 336 2672 11% /etc/config
from ls /bin, one could see that a version of Vi was present, and so on.
|Daily Giveaway - Fun Prizes from Red Hat!||Oct 25, 2016|
|Installing and Running a Headless Virtualization Server||Oct 25, 2016|
|Ubuntu MATE, Not Just a Whim||Oct 21, 2016|
|Non-Linux FOSS: Screenshotting for Fun and Profit!||Oct 20, 2016|
|Nasdaq Selects Drupal 8||Oct 19, 2016|
|Canonical Ltd.'s Ubuntu Core||Oct 19, 2016|
- Installing and Running a Headless Virtualization Server
- Daily Giveaway - Fun Prizes from Red Hat!
- Daily Giveaway
- Ubuntu MATE, Not Just a Whim
- Nasdaq Selects Drupal 8
- Build Your Own Raspberry Pi Camera
- Tech Tip: Really Simple HTTP Server with Python
- Non-Linux FOSS: Screenshotting for Fun and Profit!
- Returning Values from Bash Functions
- Secure Desktops with Qubes: Compartmentalization