Kernel Korner - Using DMA
In order to communicate the maximum addressing width, every generic device has a parameter, called the DMA mask, that contains a map of set bits corresponding to the accessible address lines that must be set up by the device driver. The DMA width has two separate meanings depending on whether an IOMMU is in use. If there is an IOMMU, the DMA mask simply represents a limitation on the bus addresses that may be mapped, but through the IOMMU, the device is able to reach every part of physical memory. If there is no IOMMU, the DMA mask represents a fundamental limit of the device. It is impossible for the device to transfer to any region of physical memory outside this mask.
The block layer uses the DMA mask when building a scatter/gather list to determine whether the page needs to be bounced. By bounce, I mean the block layer takes a page from a region within the DMA mask and copies all the data to it from the out-of-range page. When the DMA has completed, the block layer copies it back again to the out-of-range page and releases the bounce page. Obviously, this copying back and forth is inefficient, so most manufacturers try to ensure that the devices with which their server-type machines ship don't have DMA mask limitations.
DMA occurs without using the CPU, so the kernel has to provide an API to bring the CPU caches into sync with the memory changed by the DMA. One thing to remember is the DMA API brings the CPU caches up to date only with respect to the kernel virtual addresses. You must use a separate API, described in my article “Understanding Caching”, to update the caches with respect to user space.
Sometimes high-end bus chips also come with caching circuitry. The idea behind this is that writes from the CPU to the chipset are fast, but writes across the bus are slow, so if the bus controller caches the writes, the CPU doesn't need to wait for them to complete. The problem with bus posting, as this type of caching is called, is that no CPU instruction is present to flush the bus cache, so bus cache flushes work according to a strict set of rules to ensure proper ordering. First, the rules are that only memory-based writes may be cached. Writes that go through I/O space are not cached. Second, the ordering of memory-based reads and writes must be preserved strictly, even if the writes are cached. This last property allows a driver writer to flush the cache. If you issue a memory-based read to any part of the device's memory region, all cached writes are guaranteed to be issued before the read begins.
No API is available to help with posting, so driver writers need to remember to obey the bus posting rules when reading and writing a device's memory region. A good trick to remember is if you really can't think of a necessary read to flush the pending writes, simply read a piece of information from the device's bus configuration space.
The API is documented thoroughly in the kernel documentation directory (Documentation/DMA-API.txt). The generic DMA API also has a counterpart that applies only to PCI devices and is described in Documentation/DMA-mapping.txt. The intent of this section is to provide a high-level overview of all the steps necessary to get DMA working correctly. For detailed instructions, you also should read the above-mentioned documentation.
To start, when the device driver is initialized, the DMA mask must be set:
int dma_set_mask(struct device *dev, u64 mask);
where dev is the generic device and mask is the mask you are trying to set. The function returns true if the mask has been accepted and false if not. The mask may be rejected if the actual system width is narrower; that is, a 32-bit system may reject a 64-bit mask. Thus, if your device is capable of addressing all 64 bits, you first should try a 64-bit mask and fall back to a 32-bit mask if setting the 64-bit mask fails.
Next, you need to allocate and initialize the queue. This process is somewhat beyond the scope of this article, but it is documented in Documentation/block/. Once you have a queue, two vital parameters need to be adjusted. First, allow for the largest size of your SG table (or tell it to accept an arbitrarily big one) with:
void blk_queue_max_hw_segments(request_queue_t *q, unsigned short max_segments);
- Stepping into Science
- CORSAIR's Carbide Air 740
- A Better Raspberry Pi Streaming Solution
- Linux Journal December 2016
- Qu’est-ce qu’on a fait au Bon Dieu ? Télécharger Le Film Complet Gratuit
- Tyson Foods Honored as SUSE Customer of the Year
- FutureVault Inc.'s FutureVault
- Radio Free Linux
- The Tiny Internet Project, Part II
- Message for You, Sir!
Pick up any e-commerce web or mobile app today, and you’ll be holding a mashup of interconnected applications and services from a variety of different providers. For instance, when you connect to Amazon’s e-commerce app, cookies, tags and pixels that are monitored by solutions like Exact Target, BazaarVoice, Bing, Shopzilla, Liveramp and Google Tag Manager track every action you take. You’re presented with special offers and coupons based on your viewing and buying patterns. If you find something you want for your birthday, a third party manages your wish list, which you can share through multiple social- media outlets or email to a friend. When you select something to buy, you find yourself presented with similar items as kind suggestions. And when you finally check out, you’re offered the ability to pay with promo codes, gifts cards, PayPal or a variety of credit cards.Get the Guide