Using the Hammerfall HDSP on Linux
Now that the modules are loaded, and hdsploader has been run we can try to play a sound using aplay. Like any other ALSA driver, the HDSP driver mutes all channels at startup, so first you need to set the gain control, or volume, properly for your playback channels. One way to do this is to simply run alsamixer -c 1. When the bars are at 50% the channel is output with approximately 0dB gain. A more precise way is using amixer directly. The gain is as follows:
0 = -inf dB 32768 = 0 dB 65535 = +6 dB
A simple way to set all channels to 0dB gain is to use the following script:
#!/bin/bash for i in $(seq 1 18);do amixer -c 1 cset name=Chn,index=$i 32768 done
Now that you've done that, hook up your speakers to the first two analog outputs, and try the following:
aplay -D hdsp_analog some_stereo_file.wav
If all goes well you should see something like this:
Playing WAVE 'some_stereo_file.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo
By default, playback channels are connected to their respective hardware outputs; if this isn't true in your setup, you won't hear anything. If this is the case, read the following section on configuring the matrix mixer.
You also can change the -D option to send audio to different channels. For instance, using hdsp_adat would send the audio to the first two adat channels; hdsp_spdif would go to the spdif outputs. All of this is controlled by asoundrc.
If playing a sound worked, try recording a sound with arecord. This time, hook up a sound source to your first two analog channels, and run the following:
arecord -D hdsp_analog -f dat recording.wav
Press Crtl-C to halt recording. If everything worked, recording.wav should be a stereo file at 48kHz. In this case, the matrix mixer has no effect on what's recorded; the first channel recorded always corresponds to the first hardware input and so on.
As mentioned above, all software using the HDSP must be closed before switching between SingleSpeed and DoubleSpeed mode. But normally, software sets the sample rate. So what now? Well, there is a setting related to the AutoSync functionality (more on that later) that can do the job, Sample Clock Source. I won't explain exactly how it works just yet, but basically, by setting the internal clock to different frequencies, the card automatically switches modes. For instance, to switch to DoubleSpeed mode run:
amixer -c 1 cset numid=11 6
To switch back to SingleSpeed mode run:
amixer -c 1 cset numid=11 3
In both cases, don't forget to make sure that no application currently is using the sound card.
Sound routing is the most powerful feature the HDSP has to offer. Unfortunately, because it is not a feature found on many sound cards, the interface used to control it is not an ALSA standard. As of ALSA version 0.9.3, the matrix mixer interface is somewhat of a hack and is subject to change. It's possible to write values to it but not to read them back. In any case, the syntax used is source,destination,gain, where gain is as explained above, and source and destination are as follows:
For the Multiface:
input: 0-7 (analog), 16-23 (adat), 24-25 (spdif), 26-43 (playback) output: 0-7 (analog), 16-23 (adat) 24-25 (spdif), 26-27 (line out)
For the Digiface:
input_source : 0-25 (physical channels), 26-51 (playback) output_source : 0-25 (physical channels), 26-27 (line out)
The routing for the Multiface is also shown in Figure 1. By default, the playback channels are routed to the hardware output channels in order. All other possible connections are muted (0 or -inf dB gain).
To change an entry, use the following command:
amixer -c 1 cset numid=5 src,dest,gain
For instance, you could direct the SPDIF input to analog out with the following:
amixer -c 1 cset numid=5 24,0,32768 amixer -c 1 cset numid=5 25,1,32768
When you're finished, run the commands again, but with 0 as the gain instead of 32768. Don't forget that you can have multiple channels going to a single output or multiple outputs from a single input. Any combination is possible—use your imagination.
|Where's That Pesky Hidden Word?||Aug 28, 2015|
|A Project to Guarantee Better Security for Open-Source Projects||Aug 27, 2015|
|Concerning Containers' Connections: on Docker Networking||Aug 26, 2015|
|My Network Go-Bag||Aug 24, 2015|
|Doing Astronomy with Python||Aug 19, 2015|
|Build a “Virtual SuperComputer” with Process Virtualization||Aug 18, 2015|
- Concerning Containers' Connections: on Docker Networking
- Where's That Pesky Hidden Word?
- Problems with Ubuntu's Software Center and How Canonical Plans to Fix Them
- A Project to Guarantee Better Security for Open-Source Projects
- Firefox Security Exploit Targets Linux Users and Web Developers
- Doing Astronomy with Python
- My Network Go-Bag
- Build a “Virtual SuperComputer” with Process Virtualization
- Three More Lessons
- Calling All Linux Nerds!