Using the Hammerfall HDSP on Linux
Now that the modules are loaded, and hdsploader has been run we can try to play a sound using aplay. Like any other ALSA driver, the HDSP driver mutes all channels at startup, so first you need to set the gain control, or volume, properly for your playback channels. One way to do this is to simply run alsamixer -c 1. When the bars are at 50% the channel is output with approximately 0dB gain. A more precise way is using amixer directly. The gain is as follows:
0 = -inf dB 32768 = 0 dB 65535 = +6 dB
A simple way to set all channels to 0dB gain is to use the following script:
#!/bin/bash for i in $(seq 1 18);do amixer -c 1 cset name=Chn,index=$i 32768 done
Now that you've done that, hook up your speakers to the first two analog outputs, and try the following:
aplay -D hdsp_analog some_stereo_file.wav
If all goes well you should see something like this:
Playing WAVE 'some_stereo_file.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo
By default, playback channels are connected to their respective hardware outputs; if this isn't true in your setup, you won't hear anything. If this is the case, read the following section on configuring the matrix mixer.
You also can change the -D option to send audio to different channels. For instance, using hdsp_adat would send the audio to the first two adat channels; hdsp_spdif would go to the spdif outputs. All of this is controlled by asoundrc.
If playing a sound worked, try recording a sound with arecord. This time, hook up a sound source to your first two analog channels, and run the following:
arecord -D hdsp_analog -f dat recording.wav
Press Crtl-C to halt recording. If everything worked, recording.wav should be a stereo file at 48kHz. In this case, the matrix mixer has no effect on what's recorded; the first channel recorded always corresponds to the first hardware input and so on.
As mentioned above, all software using the HDSP must be closed before switching between SingleSpeed and DoubleSpeed mode. But normally, software sets the sample rate. So what now? Well, there is a setting related to the AutoSync functionality (more on that later) that can do the job, Sample Clock Source. I won't explain exactly how it works just yet, but basically, by setting the internal clock to different frequencies, the card automatically switches modes. For instance, to switch to DoubleSpeed mode run:
amixer -c 1 cset numid=11 6
To switch back to SingleSpeed mode run:
amixer -c 1 cset numid=11 3
In both cases, don't forget to make sure that no application currently is using the sound card.
Sound routing is the most powerful feature the HDSP has to offer. Unfortunately, because it is not a feature found on many sound cards, the interface used to control it is not an ALSA standard. As of ALSA version 0.9.3, the matrix mixer interface is somewhat of a hack and is subject to change. It's possible to write values to it but not to read them back. In any case, the syntax used is source,destination,gain, where gain is as explained above, and source and destination are as follows:
For the Multiface:
input: 0-7 (analog), 16-23 (adat), 24-25 (spdif), 26-43 (playback) output: 0-7 (analog), 16-23 (adat) 24-25 (spdif), 26-27 (line out)
For the Digiface:
input_source : 0-25 (physical channels), 26-51 (playback) output_source : 0-25 (physical channels), 26-27 (line out)
The routing for the Multiface is also shown in Figure 1. By default, the playback channels are routed to the hardware output channels in order. All other possible connections are muted (0 or -inf dB gain).
To change an entry, use the following command:
amixer -c 1 cset numid=5 src,dest,gain
For instance, you could direct the SPDIF input to analog out with the following:
amixer -c 1 cset numid=5 24,0,32768 amixer -c 1 cset numid=5 25,1,32768
When you're finished, run the commands again, but with 0 as the gain instead of 32768. Don't forget that you can have multiple channels going to a single output or multiple outputs from a single input. Any combination is possible—use your imagination.
Fast/Flexible Linux OS Recovery
On Demand Now
In this live one-hour webinar, learn how to enhance your existing backup strategies for complete disaster recovery preparedness using Storix System Backup Administrator (SBAdmin), a highly flexible full-system recovery solution for UNIX and Linux systems.
Join Linux Journal's Shawn Powers and David Huffman, President/CEO, Storix, Inc.
Free to Linux Journal readers.Register Now!
- Server Hardening
- BitTorrent Inc.'s Sync
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- New Container Image Standard Promises More Portable Apps
- The Humble Hacker?
- The Death of RoboVM
- Open-Source Project Secretly Funded by CIA
- The US Government and Open-Source Software
- EnterpriseDB's EDB Postgres Advanced Server and EDB Postgres Enterprise Manager
- ACI Worldwide's UP Retail Payments
In modern computer systems, privacy and security are mandatory. However, connections from the outside over public networks automatically imply risks. One easily available solution to avoid eavesdroppers’ attempts is SSH. But, its wide adoption during the past 21 years has made it a target for attackers, so hardening your system properly is a must.
Additionally, in highly regulated markets, you must comply with specific operational requirements, proving that you conform to standards and even that you have included new mandatory authentication methods, such as two-factor authentication. In this ebook, I discuss SSH and how to configure and manage it to guarantee that your network is safe, your data is secure and that you comply with relevant regulations.Get the Guide