An Introduction to FreeS/WAN, Part II
Last month I introduced FreeS/WAN, Linux's implementation of the IPSec tunneling protocol for secure virtual private networks (VPNs). For my sample configuration, I used the common scenario of remote access (RA) VPN. RA VPNs, you'll recall, are used when each remote user is expected to connect to the home network using separate connections, resulting in a one-tunnel-per-user setup.
But what happens when some or all of your remote users are connected to the same local area network (LAN)? I mentioned this type of site-to-site VPN scenario last month, but I didn't explain how to set up one. Building site-to-site VPNs with FreeS/WAN, therefore, is our focus this month.
Before we dive into FreeS/WAN configurations, let's take a quick look at architectural considerations. Figure 1 shows a typical site-to-site VPN network layout.
In Figure 1, each site's firewall acts as a tunnel endpoint. There are several good reasons to use a firewall as a VPN endpoint:
Convenience: most firewall platforms support IPSec or some other VPN protocol, eliminating the expense and time required to configure and administer separate VPN servers.
Security: a firewall acting as a VPN endpoint can regulate traffic entering and leaving VPN tunnels with excellent granularity and accuracy.
Simplicity: if your firewall and IPSec software were designed to run together on the same host, it can be much easier to get your tunnels working and to troubleshoot them when they don't.
However, there are several reasons why this type of setup may not be feasible or desirable:
Non-interoperability: if you aren't in control of both sides of the VPN tunnel (e.g., if you're connecting to a vendor's or partner's network), the remote firewall's VPN implementation may not be compatible with your firewall's.
Performance: if your firewall is already fully or over-subscribed doing its normal duties, it may not be able to support the added overhead of VPN authentication and encryption.
In Figure 2, each VPN endpoint is a dedicated computer (in Figure 2 both endpoints are set up this way, but you can also mix and match, say, a combined firewall/VPN endpoint on one end and a split on the other). It may seem reckless to put any device in parallel with your firewall. Couldn't such a device be used as a back door?
Indeed, it could—unless the VPN server is carefully configured to accept only VPN traffic and its VPN software is carefully configured to accept VPN connections from only approved endpoints, i.e., using strong authentication mechanisms.
Let's jump right into FreeS/WAN and see how to set up a site-to-site VPN with endpoints secure enough to reside either on firewalls or on standalone hosts.
Figure 3 shows a site-to-site VPN scenario that's functionally equivalent to the one in Figure 1. That is, it also has the same host at each site serving as a combined Linux firewall and FreeS/WAN IPSec server. Figure 3, however, offers a bit more detail. First, you can see that each network is connected to the Internet via a local router. Second, Figure 3 shows the IP addresses needed for tunnel definitions (we'll see which IPs get used where shortly).
In this scenario, we need to set up a VPN tunnel between two sites' firewalls' respective “external” interfaces. When a user on one site's LAN wishes to communicate with a host on the other LAN, the firewall sends those packets through the tunnel. Reply packets take the same path back through the tunnel. Hosts on either side may initiate connections through the tunnel.
The firewalls restrict what sort of data may enter and leave the tunnel at either side. On a combined iptables/FreeS/WAN server, these firewall rules can be the same, as though no tunnel were being used, even if network address translation (NAT) is involved. This point is explained later in this article.
A few important premises about this scenario should be noted. First, both firewalls are running Linux kernel version 2.4.18. Second, both firewalls' kernels have been patched with FreeS/WAN version 1.97 and had the user-space FreeS/WAN tools (same version) installed as well. Third, the two networks can reach each other without IPSec, i.e., in the clear. (We don't want them to communicate that way, but we need to know they could; otherwise troubleshooting VPN problems are much harder.)
|Geek Hide-away in Guatemala - Stay for Free!||Nov 26, 2015|
|Microsoft and Linux: True Romance or Toxic Love?||Nov 25, 2015|
|Non-Linux FOSS: Install Windows? Yeah, Open Source Can Do That.||Nov 24, 2015|
|Cipher Security: How to harden TLS and SSH||Nov 23, 2015|
|Web Stores Held Hostage||Nov 19, 2015|
|diff -u: What's New in Kernel Development||Nov 17, 2015|
- Microsoft and Linux: True Romance or Toxic Love?
- Cipher Security: How to harden TLS and SSH
- Non-Linux FOSS: Install Windows? Yeah, Open Source Can Do That.
- Web Stores Held Hostage
- Firefox's New Feature for Tighter Security
- Geek Hide-away in Guatemala - Stay for Free!
- PuppetLabs Introduces Application Orchestration
- diff -u: What's New in Kernel Development
- It's a Bird. It's Another Bird!
- IBM LinuxONE Provides New Options for Linux Deployment