Real Time and Linux
Consequently, real-time applications usually give themselves a high priority, lock themselves in memory (and don't grow their memory usage), use lock-free communication whenever possible, use cache memory wisely, avoid nondeterministic I/O (e.g., sockets) and execute within a suitably constrained system. Suitable constraints include limiting hardware interrupts, limiting the number of processes, curtailing system call use by other processes and avoiding kernel problem areas, e.g., don't run hdparm.
Some of the system calls that should be made by a real-time application require special privileges. This usually is accomplished by having root be the owner of the process (having a shell owned by root run the program or having the executable file have the SUID bit set). A newer way is to make use of the capability mechanism. There are capabilities for locking down memory, such as CAP_IPC_LOCK (that "IPC'' is in the name is just something we need to accept), and for being able to set real-time priorities, which can be done with the capability CAP_SYS_NICE.
A real-time process sets its priority with sched_setscheduler(2). The current implementation provides the standard POSIX policies of SCHED_FIFO and SCHED_RR, along with priorities ranging in value from 1-99. Bigger is better. The POSIX function to check the maximum allowable priority value for a given policy is sched_get_priority_max(2).
A real-time process should lock down its memory and not grow. Locking memory is done in Linux with the POSIX standard function mlockall(2). Usually one uses the flags value of MCL_CURRENT | MCL_FUTURE to lock down current memory and any new memory if one's process grows in the future. While growing often is not acceptable, if you get lucky and survive the delay you might as well get the newly allocated memory locked down as well. Be careful to grow your stack and allocate all dynamic memory, and then call mlockall(2) before your process begins its time-critical phase. Note that you can check to see if your process had any page faults during a section of code by using getrusage(2). I show a code fragment below to illustrate the use of several functions. Note that one should check the return value from each of these calls and read the man pages for more details:
priority = sched_get_priority_max(SCHED_FIFO); sp . sched_priority = priority; sched_setscheduler(getpid(), SCHED_FIFO, &sp); mlockall(MCL_FUTURE | MCL_CURRENT); getrusage(RUSAGE_SELF,&ru_before); . . . // R E A L T I M E S E C T I O N getrusage(RUSAGE_SLEF,&ru_after); minorfaults = ru_after.ru_minflt - ru_before.ru_minflt; majorfaults = ru_after.ru_majflt - ru_before.ru_majflt;
There are a number of efforts to benchmark various aspects of Linux. Real-time application developers are most interested in interrupt latency, timer granularity, context-switch time, system call overhead and kernel preemptibility. Interrupt latency is the time from when a device asserts an interrupt until the time that the appropriate interrupt handler begins executing. This typically is delayed by the handling of other interrupts and by interrupts being disabled. Linux does not implement interrupt priorities. Most interrupts are blocked when Linux is handling an interrupt. This time typically is quite short, however, perhaps a few microseconds.
On the other hand, the kernel may block interrupts for a significantly longer time. The intlat program from Andrew Morton allows one to measure interrupt latencies (http://www.uow.edu.au/~andrewm/linux/#intlat/). Similarly, his schedlat shows scheduling latencies (http://www.uow.edu.au/~andrewm/linux/schedlat.html).
Context-switch time is included in the well-known benchmark harness LMbench (http://www.bitmover.com/lmbench/), as well as by others (http://www.atnf.csiro.au/~rgooch/benchmarks/linux-scheduler.html, http://math.nmu.edu/~benchmark/index.php?page=context). LMbench also provides information about system calls.
In Table 1 we show the results of LMbench. This table shows context-switch times. The benchmark program was run three times, and the lowest value for the context-switch time for each configuration is reported in the table as per the documentation for LMbench. The highest value, however, was no more than about 10% larger than the minimum. The size of the process is reported in kilobytes, the context-switch time is in microseconds. The context-switch time data indicate that substantial use of data in the cache causes significantly larger context-switch times. The context-switch time includes time to restore the cache state.
As an example of interrupt-off times, one can see some results at http://www.uow.edu.au/~andrewm/linux/intlat/intlat-disk.html. In one experiment with hdparm, the data show that interrupts can be disabled for over 2ms while hdparm runs. Developers can use the intlat mechanism to measure interrupt-off times for the system they are running. It is only under rare conditions that interrupt-off times will exceed 100µs. These conditions should be avoidable for most embedded systems. They are the areas that Morton warns against.
An area of more significant concern to most real-time developers is that of scheduling latency. That is, the delay in continuing a newly awakened high-priority task. A long delay is possible when the kernel is busy executing a system call. This is because the Linux kernel will not preempt a lower priority process in the midst of a system call in order to execute a newly awakened higher priority process. This is why the Linux kernel is termed non-preemptible.
The latency test from Benno Senoner shows that a delay of 100ms or more is possible (http://www.gardena.net/benno/linux/audio/). We can see that both interrupt blocking and scheduling latencies can be sufficiently long to prevent satisfactory performance for some applications.
Timing resolution is also of importance to many embedded Linux developers. For example, the setitimer(2) function is used to set a timer. This function, like other time functions in Linux, has a resolution of 10ms. Thus, if one sets a timer to expire in 15ms, it actually will expire in about 20ms. In a simple test measuring the time interval between 1,000 successive 15ms timers, we found that the average time interval was 19.99ms, the minimum time was 19.987ms and the maximum time was 20.042ms on a quiescent system.
Kevin Dankwardt is founder and CEO of K Computing, a training and consulting firm in Silicon Valley. In particular, his organization develops and delivers embedded and real-time Linux training worldwide.
|illusive networks' Deceptions Everywhere||Aug 29, 2016|
|Happy Birthday Linux||Aug 25, 2016|
|ContainerCon Vendors Offer Flexible Solutions for Managing All Your New Micro-VMs||Aug 24, 2016|
|Updates from LinuxCon and ContainerCon, Toronto, August 2016||Aug 23, 2016|
|NVMe over Fabrics Support Coming to the Linux 4.8 Kernel||Aug 22, 2016|
|What I Wish I’d Known When I Was an Embedded Linux Newbie||Aug 18, 2016|
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- illusive networks' Deceptions Everywhere
- Happy Birthday Linux
- What I Wish I’d Known When I Was an Embedded Linux Newbie
- New Version of GParted
- ContainerCon Vendors Offer Flexible Solutions for Managing All Your New Micro-VMs
- Updates from LinuxCon and ContainerCon, Toronto, August 2016
- Tor 0.2.8.6 Is Released
- All about printf
- Blender for Visual Effects