Firebox II

 in
This Seattle-based company makes a line of dedicated firewall appliances to serve anything from the SOHO market to a 5,000-user mega-office with up to 100 branches on Virtual Private Networks connected securely across the Internet.
  • Manufacturer: Watchguard Technologies, Inc.

  • E-mail: information@watchguard.com

  • URL: http://www.watchguard.com/

  • Price: $4,990 US (Firebox II; options extra), $449 US (base SOHO)

  • Reviewer: Glenn Stone

Much ado has been made in the post-Melissa era about firewalling, particularly with the advent of low-cost, always-on high-speed Internet connections and associated security risks. Many of us here are familiar with the poor but educated man's approach to the problem: drop a Linux distro on a machine with a pair of NICs and configure appropriately. This is cheap, effective, reasonably secure, but also time-consuming and doesn't scale all that well. It's fine for Joe Hobbyist, but Mike the Network Manager wants something a little easier to handle.

Enter Watchguard. This Seattle-based company makes a line of dedicated firewall appliances to serve anything from the SOHO market to a 5,000-user mega-office with up to 100 branches on Virtual Private Networks connected securely across the Internet. Bundled with the bigger boxes is their LiveSecurity System, a GUI-based manager tool that allows the network manager to easily configure the local firewall, called a Firebox, and optionally, VPN Manager, which allows management of multiple VPNs as well as any Fireboxes (including the SOHOs) that happen to be on the other end of the VPN link. As you might have guessed, the larger Fireboxes run Linux. (The SOHOs run VxWorks.) At $4,990 US for a full-sized one, it's not cheap at all but, as I was to find out, it is easy.

Initial Impressions

The Firebox II arrived in a nice carry-handle box with all the cables needed to hook it up, including an RJ-45 crossover cable for setup, RJ-45 patch cords for the rest of the network and a serial cable for direct console setup with appropriate adapters for DB9 or DB25 connectors. The fire-engine red case also comes with a pair of metal flanges that, when you rearrange them appropriately, allow the Firebox to be mounted in a standard 19", 2U rack slot. The front panel has an array of LEDs for system status, traffic and load average; the back panel has three RJ-45 10/100Tx jacks, a pair of DB9 serial ports, a pair of Type II PCMCIA modem slots, power socket and switch. (I always liked the idea of the switch on the front, but that's just me.) Under the hood lies a custom single-board computer with a 200MHz Pentium MMX, 64MB of SDRAM, an 8MB Flash ROM and two noisy but effective fans. Instead of a CPU fan, there is a monster heat sink, and one of the case fans is aimed directly at it. I suppose this is so the unit can survive the loss of one of the fans; using a smaller fanned-heat sink would give the unit a single point of failure.

The manual is a nice 300-page spiral-bound volume about the size of a trade paperback. What lay inside, though, was the big surprise—Windows?!? You need Microsoft Windows to run this software.

A query to Watchguard's tech support web page netted me a pair of answering phone calls, verifying what the manual said. There is currently no way to set up the big Fireboxes without using Microsoft Windows. But, they said, we would be happy to have you visit our training facility and show you how things work.

On-site at Watchguard, we get down to business. We put the CD in the drive, the install ran, did its normal Windowsish thing (including a reboot) and now we're looking at the configurator for the Firebox. You can configure it for drop-in mode (where it does transparent proxy like a bridge) or routed mode, which allows the trusted network to have private addresses, to which the Firebox will port-forward, if so desired. With all the requisite magic numbers in place, we pressed the button to upload and booted the Firebox. Hmmm, uploading via TCP didn't work. Not to worry, you can also upload via the console port. Back up a click, reset for COM1 and up pops the progress box. Ahh, sweet success. A reboot under software control, and the Firebox is up and running. We verified that it would communicate over the trusted interface then used a pre-configured Firebox to address it over the external interface, set up an IPSec gateway and tunnel. The optional VPN Manager is really slick; you simply give it the remote address and configuration password of the remote Firebox, then drag one Firebox icon onto another, run through three clicks worth of configuration and the tunnel is configured; a quick reset (20-30 seconds) on each Firebox, and the tunnel is active. The VPN tunnels can be filtered in all the same ways you can filter regular IP traffic: by host, by port or both, on source, destination or both. The Firebox II client can also configure SOHO units remotely, so a network admin can manage his or her telecommuters as well as big branches.

I asked some pointed questions about the safety of uploading new configurations and got a neat insight into the Firebox's internal architecture. The Flash ROM is divided into several sections: the running configuration, the underlying Linux system, a backup area where these can be saved (and recovered) during upgrades and a “system” area, which is the moral equivalent of a rescue partition. You tell the configurator you want to restore the factory default configuration, then reboot the system with the console port connected to your serial port. The configurator detects the boot prompt and tells the system to boot from the system area, at which point you reconfigure the machine from scratch. You can also boot the box with a PCMCIA modem in one of its slots and (re-)configure the machine from remote dialup. This makes for easy physical deployment of a large VPN; all the person at the remote site has to do is insert various sets of tab “A” into slot “B” (and the cables are all color-coded) and turn it on, and the network admin sitting in the home office in Sioux City can take it from there.

______________________

Webinar
One Click, Universal Protection: Implementing Centralized Security Policies on Linux Systems

As Linux continues to play an ever increasing role in corporate data centers and institutions, ensuring the integrity and protection of these systems must be a priority. With 60% of the world's websites and an increasing share of organization's mission-critical workloads running on Linux, failing to stop malware and other advanced threats on Linux can increasingly impact an organization's reputation and bottom line.

Learn More

Sponsored by Bit9

Webinar
Linux Backup and Recovery Webinar

Most companies incorporate backup procedures for critical data, which can be restored quickly if a loss occurs. However, fewer companies are prepared for catastrophic system failures, in which they lose all data, the entire operating system, applications, settings, patches and more, reducing their system(s) to “bare metal.” After all, before data can be restored to a system, there must be a system to restore it to.

In this one hour webinar, learn how to enhance your existing backup strategies for better disaster recovery preparedness using Storix System Backup Administrator (SBAdmin), a highly flexible bare-metal recovery solution for UNIX and Linux systems.

Learn More

Sponsored by Storix