SuSE Linux 7.0
The partitions are set up, and we move to the installation of 341 packages. As the install progresses, you get a typical status screen displaying the package name being installed, a short description, and an overall progress update and percentage of disk space consumed. The installation I selected uses a little over 1GB of space.
At 242 packages, I am informed that the LILO boot sector has been set up, and I can restore the old one with the command:
lilo -u /dev/hda
Then the installer starts the new system, and a text screen tells me the base system has been successfully installed. The graphical YaST2 continues, asking for CD2, then resumes installing packages. Another pause at package 326, and I'm asked for CD3. Another pause at 331 for CD4.
Now we move on to X set up. I am asked for my monitor, a Mag MX17, and then the video card, which it correctly identifies as an ATI and sets for 1240x1168@16bpp. I try the test at this resolution, my color palette shifts to an unusual look and the system appears to lock up. I can't switch to a different VT, nor does CTL-ALT-Backspace or CTL-ALT-DEL have any effect, so I resort to the reset button. The system boots into SuSE and runs checks on the file systems since it wasn't shut down properly, then gets me back into YaST2 at the monitor configuration. This was nice. Even though I hit a major problem, the install recovered and resumed where I left off. This time I try a more conservative setting, 640x480@8bpp—and get a black screen and another lockup. Hmm. Seems the ATI driver has a problem with my card. There is no option to override with a generic SVGA card, so I opt for no X11 and move on. The install does tell me I can set X up later with SaX.
From here, YaST2 moves on to setting up the printers, sound, Internet and network. I do not have a modem on this machine, and YaST2 tells me it has not detected a modem or ISDN adapter. It does recognize my Creative sound card and my 3Com NIC. I go ahead and set up my IP address with the default gateway through my file server and a host name with DNS pointing to my ISP's name servers. The install checks to certify that I have entered valid IP addresses.
YaST2 tells me the NIC was configured correctly and networking is set up, which I verify by pinging the box from my file server. Looks good!
The sound card setup allows me to set the volume and test, and it plays a nice little orchestral piece—good again! Later on I look at the loaded modules, and it looks like sound is handled by ALSA.
For printing, I have an HP print server on the LAN with a NEC Silentwriter and an HP Deskjet 693C. The installer scanned the local LAN for hosts and failed to find anything, probably because I'm not running DNS on the server. Since I have a custom lpr script on the server that powers up my printers via an X10 control module when I need to print, I route the print jobs to the file server, using its IP address, and it takes care of the filtering too. One minor annoyance here is the first network printer is called “remote” with no opportunity to override that name except on the second printer. I would rather have preferred setting it to something more descriptive.
That was it on this screen, so I moved on to “Finish Installation”, and was told I could log in as “stew”. The manual reminds you to change your BIOS settings back to boot from hard drive and/or floppy.
I log in, do a ps -ax to see what is running—looks normal enough, httpd, lpd and several copies of nscd, which the man pages tell me is a name server caching dæmon—okay. lynx localhost gets me to some local SuSE pages—good. My server is on line, so I try lynx on some remote web pages, and they come up too. Looks like networking is working fine.
I take a quick visit to the SuSE web site and search their support database to see if I see anything on my X issues, but the info seems to refer only to SuSE6.4 and older versions, so I forge ahead on my own.
To see if I could pick up anything on my X issues I do an
rpm -q -a | grep mach
from the command line. I see the following:
xmach64-3.3.6-44This explains my problems since YaST2 was trying to use the XFree4.0 server. Doing a similar search on xf
rpm -q -a | grep xf86 xf86-4.0-55 xf86_3x-3.3.6-44It looks like sticking with XFree3.3.6 would be the wise thing to do. I log out and re-log in as root to finish setting things up.
I was able to run SaX from the command line and correctly configure XFree3.3.6 by manually choosing my ATI video card, an Xpression card. Then I was able to fine tune the settings and get it set up for 1024x768@16bpp. The card is an older card with only 2MB VRAM, so this is about as good as it gets. Running startx, I am in the KDE desktop. SaX uses XFree 3.3.6 vs. SaX2, which uses XFree4.0.
Fast/Flexible Linux OS Recovery
On Demand Now
In this live one-hour webinar, learn how to enhance your existing backup strategies for complete disaster recovery preparedness using Storix System Backup Administrator (SBAdmin), a highly flexible full-system recovery solution for UNIX and Linux systems.
Join Linux Journal's Shawn Powers and David Huffman, President/CEO, Storix, Inc.
Free to Linux Journal readers.Register Now!
- Ubuntu Online Summit
- Devuan Beta Release
- The Qt Company's Qt Start-Up
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- May 2016 Issue of Linux Journal
- The US Government and Open-Source Software
- Open-Source Project Secretly Funded by CIA
- EnterpriseDB's EDB Postgres Advanced Server and EDB Postgres Enterprise Manager
- The Death of RoboVM
- New Container Image Standard Promises More Portable Apps
In modern computer systems, privacy and security are mandatory. However, connections from the outside over public networks automatically imply risks. One easily available solution to avoid eavesdroppers’ attempts is SSH. But, its wide adoption during the past 21 years has made it a target for attackers, so hardening your system properly is a must.
Additionally, in highly regulated markets, you must comply with specific operational requirements, proving that you conform to standards and even that you have included new mandatory authentication methods, such as two-factor authentication. In this ebook, I discuss SSH and how to configure and manage it to guarantee that your network is safe, your data is secure and that you comply with relevant regulations.Get the Guide