Linux Job Scheduling
This is the area that confuses users of cron the most. They specify commands they run every day from their interactive shells, and then they put them in their crontab and they don't work or they behave differently than they expected.
For example, if you write a program called “fardels” and put it in &HOME/bin, then add $HOME/bin to your PATH, cron might send you mail like this:
/bin/sh: fardels: command not found
The PATH cron uses is not necessarily the same as the one your interactive shell uses.
It is necessary to understand that the environment in which cron jobs run is not the environment in which they operate every day.
First of all, none of their normal environment variables are initialized as they are in their login shells. The following environment variables are set up by the cron dæmon:
SHELL=/bin/sh LOGNAME set from /etc/passwd entry for the crontab's UID. HOME set from /etc/passwd entry for the crontab's UID.
We've been holding out on you. There's another kind of entry allowed in your crontab file. Lines of the form iname=value are allowed to set environment variables that will be set when jobs are run out of the crontab. You may set any environment variable except LOGNAME.
An important one to note is MAILTO. If MAILTO is undefined, the output of jobs will be mailed to the user who owns the crontab. If MAILTO is defined but empty, mailed output is suppressed. Otherwise, you may specify an e-mail address to which to send the output of cron jobs.
Finally, any percent sign in the command portion of a job entry is treated as a newline. Any data which follows the first percent sign is passed to the job as standard input, so you can use this to invoke an interactive program on a scheduled basis.
The ability to have and use a crontab is controlled in a manner very similar to the at subsystem. Two files, /etc/cron.allow and /etc/cron.deny, determine who can use crontab. Just as in the case of at, the cron.allow is checked first. If it exists, only the users listed there may have cron jobs. If it does not exist, the cron.deny file is read. All users except those listed there may have cron jobs.
If neither file exists (and this is quite unlike “at”), all users may have crontabs.
There is hardly anything to document here. The cron dæmon (which is called either cron or crond) takes no arguments and does not respond to any signals in a special way. It examines the /var/spool/cron directory at start-up for files with names matching user names in /etc/passwd. These files are read into memory. Once per minute, cron wakes up and walks through its list of jobs, executing any that are scheduled for that minute.
Each minute, it also checks to see if the /var/spool/cron directory has changed since it was last read, and it rereads any modifications, thus updating the schedule automatically.
I've led you through a merry dance so far. I've got you thinking that only users have crontabs, and that all scheduled jobs run as the crontab's owning user. That's almost true. Cron also has a way to specify crontabs at a “system” level. In addition to checking /var/spool/cron, the cron dæmon also looks for an /etc/crontab and an /etc/cron.d directory.
The /etc/crontab file and the files in /etc/cron.d are “system crontabs”. These have a slightly different format from that discussed so far.
The key difference is the insertion of a field between the “day of week” field and the command field. This field is “run as user” field. Thus:
02 4 * * * root run-parts /etc/cron.daily
will run “run-parts /etc/cron.daily” as root at 2 minutes past 4 a.m. every single day.
There you have it. While Linux does not ship with a mature and complete batch process management tool, still the combination of at and cron permit considerable flexibility and power.
Bear in mind that we have covered the Linux versions of these tools as shipped with most current distributions. While just about every UNIX system on the market has these tools, some things vary.
Expect at queues to be different. Not all crons support names or ranges. Most do not support lists of ranges or the increment feature. No other cron with which I am familiar supports setting environment variables in the crontab. I don't think any other at supports “teatime” as a time specification.
This boils down to a basic piece of advice. Always check the local documentation. If in doubt, experiment.
Michael Schwarz (firstname.lastname@example.org) is a consultant with Interim Technology Consulting in Minneapolis, Minnesota. He has 15 years of experience writing UNIX software and heads up the open-source SASi project. He has been using Linux since he downloaded the TAMU release in 1994, and keeps the SASi project at http://alienmystery.planetmercury.net/.
|illusive networks' Deceptions Everywhere||Aug 29, 2016|
|Happy Birthday Linux||Aug 25, 2016|
|ContainerCon Vendors Offer Flexible Solutions for Managing All Your New Micro-VMs||Aug 24, 2016|
|Updates from LinuxCon and ContainerCon, Toronto, August 2016||Aug 23, 2016|
|NVMe over Fabrics Support Coming to the Linux 4.8 Kernel||Aug 22, 2016|
|What I Wish I’d Known When I Was an Embedded Linux Newbie||Aug 18, 2016|
- illusive networks' Deceptions Everywhere
- Happy Birthday Linux
- New Version of GParted
- What I Wish I’d Known When I Was an Embedded Linux Newbie
- All about printf
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- Updates from LinuxCon and ContainerCon, Toronto, August 2016
- ContainerCon Vendors Offer Flexible Solutions for Managing All Your New Micro-VMs
- Blender for Visual Effects
With all the industry talk about the benefits of Linux on Power and all the performance advantages offered by its open architecture, you may be considering a move in that direction. If you are thinking about analytics, big data and cloud computing, you would be right to evaluate Power. The idea of using commodity x86 hardware and replacing it every three years is an outdated cost model. It doesn’t consider the total cost of ownership, and it doesn’t consider the advantage of real processing power, high-availability and multithreading like a demon.
This ebook takes a look at some of the practical applications of the Linux on Power platform and ways you might bring all the performance power of this open architecture to bear for your organization. There are no smoke and mirrors here—just hard, cold, empirical evidence provided by independent sources. I also consider some innovative ways Linux on Power will be used in the future.Get the Guide