RTAI: Real-Time Application Interface
The real-time task is implemented similarly to RTAI; i.e., it is written and compiled as a kernel module which is loaded into the kernel after the required RTAI core module(s) has been loaded. This architecture yields a simple and easily maintained system that allows dynamic insertion of the desired real-time capabilities and tasks. The example below shows all that is required for a task to be scheduled in real time:
insmod /home/rtai/rtai insmod /home/rtai/modules/rtai_fifo insmod /home/rtai/modules/rtai_sched insmod /path/rt_process
To stop your application and remove the RTAI:
rmmod rt_process rmmod rtai_sched rmmod rtai_fifo rmmod rtaiThe facilities ldmod and remod may be used to load and unload the core modules.
RTAI's task scheduler allows hard real-time, fully preemptive scheduling based on a fixed-priority scheme. All schedules can be managed by timing functions and real-time events such as semaphore acquisition, clocks and timing functions, asynchronous event handlers, and include inter-task synchronization.
RTAI supports both one-shot and periodic timers on Pentium and 486-class CPUs. Although both periodic and one-shot timers are supported, they may not be instantiated simultaneously; i.e., one-shot and periodic tasks may not be loaded into the kernel as modules at the same time.
Using these timers (instantiated by rtai_sched), periodic rates in excess of 90KHz are supported, depending on the CPU, bus speed and chip set performance. On Pentium processors, one-shot task rates in excess of 30KHz are supported (Pentium II, 233 MHz), and on 486 machines, the one-shot implementation provides rates of about 10KHz, all while retaining enough spare CPU time to service the standard Linux kernel.
The limitation of rtai_sched to support simultaneously one-shot and periodic timers is mitigated by the MultiUniProcessor (MUP) real-time scheduler (rtai_mups), which provides the capability to use, simultaneously, both a periodic and a one-shot timer or two periodic timers with different periods, at a performance equivalent to that noted above under rtai_sched. Note that, since the MUP uses the APIC (advanced programmable interrupt controller) timer, it cannot operate under SMP and requires each MUP-scheduled task to be locked to a specific CPU (thus the MultiUniProcessor designation); however, the MUP retains all coordination and IPC services, so that no other capabilities are lost.
Floating-point operations within real-time tasks/ISRs (interrupt service routines) are possible, provided these tasks are marked, upon loading, as tasks which require the FPU. This method provides real-time task access to the FPU while still allowing FPU access to standard Linux tasks.
RTAI provides efficient and immediate access to the hardware by allowing, if one chooses, interaction directly with the low-level PC hardware, without first passing through the interrupt management layers of the standard Linux kernel.
The ability to individually assign specific IRQs to specific CPUs, as described in further detail below, allows immediate, responsive and guaranteed interface times to the hardware.
The term inter-process communication (IPC) describes different ways of message passing between active processes or tasks, and also describes numerous forms of synchronization for the data transfer.
Linux provides standard system V IPC in the form of shared memory, FIFOs, semaphores, mutexes, conditional variables and pipes which can be used by standard user processes to transfer and share data. Although these Linux IPC mechanisms are not available to do real-time tasks, RTAI provides an additional set of IPC mechanisms which include shared memory, message queues, real-time FIFOs, mutexes, semaphores and conditional variables. These are used to transfer and share data between tasks and processes in both the real-time and Linux user-space domains.
RTAI's remote procedure call (RPC) mechanism is similar in operation to QNX messages available to real-time tasks, and transfers either an unsigned integer or a pointer to the destination task(s).
The RTAI mailbox implementation provides the ability to send any message from user space to real-time tasks, real-time tasks to real-time tasks, and user tasks to user tasks (using LXRT) via any definable mailbox buffer size. Multiple senders and receivers are allowed, where each is serviced according to its priority.
|Android Candy: Copay—the Next-Generation Bitcoin Wallet||Sep 03, 2015|
|The True Internet of Things||Sep 02, 2015|
|September 2015 Issue of Linux Journal: HOW-TOs||Sep 01, 2015|
|September 2015 Video Preview||Sep 01, 2015|
|Using tshark to Watch and Inspect Network Traffic||Aug 31, 2015|
|Where's That Pesky Hidden Word?||Aug 28, 2015|
- Using tshark to Watch and Inspect Network Traffic
- Problems with Ubuntu's Software Center and How Canonical Plans to Fix Them
- The True Internet of Things
- September 2015 Issue of Linux Journal: HOW-TOs
- Android Candy: Copay—the Next-Generation Bitcoin Wallet
- Firefox Security Exploit Targets Linux Users and Web Developers
- Where's That Pesky Hidden Word?
- Concerning Containers' Connections: on Docker Networking
- A Project to Guarantee Better Security for Open-Source Projects
- Doing Astronomy with Python