Introduction to Sybase, Part 2

This month Mr. Sissom shows us how to set up and use a Sybase client written in Perl through examples.

Last month, we installed a Sybase database server. This month, we will install a client to access our server. First, we need to understand how the Sybase network interface works.

A Sybase client must create a network connection to a database server when it needs to access resources in the database (see Figure 1). Sybase has created a protocol to communicate over the network. This protocol is called the Tabular Data Stream (TDS) protocol. It operates on top of other networking protocols such as TCP/IP on UNIX systems or IPX/SPX on Novell networks. TDS is a proprietary protocol and not documented by Sybase. Fortunately, Sybase has created client libraries which can be used to communicate with the server. A group of people have tried to reverse-engineer the TDS protocol. Look at for more information.

Figure 1. TDS Protocol

Sybase supports two interfaces to the database. DB-Library is an API that has been used for quite awhile in Sybase products. I believe it is supported for backwards compatibility, and may not be supported in a future version of the product. CT-Library is the API Sybase created for version 10 and higher products. It supports advanced features such as cursors and asynchronous query processing. You don't need to understand these features to do basic processing with your database server. We will use CT-Library to communicate with our server.

We could write our client using C or C++. The libraries required to do this are included with the server. Look for examples in the sample directory under the server directory. There is a subdirectory for DB-Library and one for CT-Library. We don't have to use C or C++, however. An extension to the Perl language called sybperl enables the use of Perl to write clients to access the database.

Most Linux distributions come with the Perl language. On my system, I have installed Red Hat 5.1 which includes Perl version 5 by default. Fortunately, it is possible to install sybperl without recompiling Perl. Using this method precludes the use of the DB-Library, which is why we have chosen to use CT-Library.

If Perl is not installed on your system, install it now. If your distribution does not provide perl, you can download the source from CPAN (

Install sybperl

First, we must download sybperl from

The newest version available at the time of this writing is version 2.09_05 in the file sybperl-2.09_05.tar.gz (148KB). Change directories to the location of the sybperl tar file, and issue the command:

perl Makefile.PL

Change to the sybperl directory just created, and edit the CONFIG file. In the line DBLIBVS=1000, change the 1000 to 0. Make sure the line SYBASE=/opt/sybase contains the correct directory for the Sybase server. The line EXTRA_LIBS=-ltli must be changed to EXTRA_LIBS=-linsck.

We will build sybperl to work with CT-library. Most Linux distributions come with the Berkeley DB library. If Perl is configured to use this library, a conflict arises when using DB-library at the same time, since both use the call open_database. If you recompile Perl to leave out the Berkeley DB library, you can leave the line DBLIBVS=1000 in the CONFIG file and use DB-library.

Save the changes to the CONFIG file, then issue this command:

perl Makefile.PL

This will create a file that will build the software. It looks for the Perl installation in your path. If Perl isn't in your path, you'll need to change your path to include it. Now issue the make command to build the software; it will take a few minutes to run. sybperl has tests that can be run to ensure it is built properly. To run these tests, edit the PWD file to put your sa password and the name of your Sybase server on the proper lines. If you installed the server following the directions in the last issue, the name of the server is linux_dev. Save the file, then type the command

make test
This command will run a series of tests. If everything is working properly, the message “All tests successful” will be printed.

Now, let's install sybperl. If your Perl installation is in a directory that requires root access to modify, change to root using su. Run the command

make install

Perl and sybperl are now installed, so it is time to write some programs.


Free Dummies Books
Continuous Engineering


  • What continuous engineering is
  • How to continuously improve complex product designs
  • How to anticipate and respond to markets and clients
  • How to get the most out of your engineering resources

Get your free book now

Sponsored by IBM

Free Dummies Books
Service Virtualization

Learn to:

  • Define service virtualization
  • Select the most beneficial services to virtualize
  • Improve your traditional approach to testing
  • Deliver higher-quality software faster

Get your free book now

Sponsored by IBM