Hack and / - Bond, Ethernet Bond
As you might imagine, Debian's network configuration is quite different from Red Hat's. Unfortunately, I don't have a Perl script to automate the process for Debian users, but as you will see, it's so simple, a script isn't necessary. All the network configuration for Debian-based servers can be found in /etc/network/interfaces. Here's a sample interfaces file:
# The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.19.64 netmask 255.255.255.0 gateway 192.168.19.1
To configure a bonded interface, I simply comment out all of the configuration settings for eth0 and create a new configuration for bond0 that copies all of eth0's settings. The only change I make is the addition of an extra parameter called slaves that lists which interfaces should be used for this bonded interface:
# The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet static # address 192.168.19.64 # netmask 255.255.255.0 # gateway 192.168.19.1 auto bond0 iface bond0 inet static address 192.168.19.64 netmask 255.255.255.0 gateway 192.168.19.1 slaves eth0 eth1
Once you have made the changes, type sudo service networking restart or sudo /etc/init.d/networking restart to restart your network interface.
No matter whether you use Red Hat or Debian, once you have configured the bonded interface, you can use the ifconfig command to see that it has been configured:
$ sudo ifconfig bond0 Link encap:Ethernet HWaddr 00:0c:29:28:13:3b inet addr:192.168.19.64 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe28:133b/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:38 errors:0 dropped:0 overruns:0 frame:0 TX packets:43 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16644 (16.2 KB) TX bytes:3282 (3.2 KB) eth0 Link encap:Ethernet HWaddr 00:0c:29:28:13:3b UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:37 errors:0 dropped:0 overruns:0 frame:0 TX packets:43 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16584 (16.1 KB) TX bytes:3282 (3.2 KB) Interrupt:17 Base address:0x1400 eth1 Link encap:Ethernet HWaddr 00:0c:29:28:13:3b UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:60 (60.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x1480 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Once the bonded interface is enabled, you can ping the server from a remote host and test that it fails over when you unplug one of the Ethernet cables. Any failures should be logged both in dmesg (/var/log/dmesg) and in the syslog (/var/log/messages or /var/log/syslog) and would look something like this:
Oct 04 16:43:28 goldfinger kernel: [ 2901.700054] eth0: link down Oct 04 16:43:29 goldfinger kernel: [ 2901.731190] bonding: bond0: link status definitely down for interface eth0, disabling it Oct 04 16:43:29 goldfinger kernel: [ 2901.731300] bonding: bond0: making interface eth1 the new active one.
As I said earlier, I highly recommend you experiment with each bonding mode and with different types of failures, so you can see how each handles both failures and recoveries on your network. When your system is more tolerant of failures, you'll find you are more tolerant of your system.
Kyle Rankin is a Systems Architect in the San Francisco Bay Area and the author of a number of books, including The Official Ubuntu Server Book, Knoppix Hacks and Ubuntu Hacks. He is currently the president of the North Bay Linux Users' Group.
Kyle Rankin is a director of engineering operations in the San Francisco Bay Area, the author of a number of books including DevOps Troubleshooting and The Official Ubuntu Server Book, and is a columnist for Linux Journal.
|September 2015 Issue of Linux Journal: HOW-TOs||Sep 01, 2015|
|September 2015 Video Preview||Sep 01, 2015|
|Using tshark to Watch and Inspect Network Traffic||Aug 31, 2015|
|Where's That Pesky Hidden Word?||Aug 28, 2015|
|A Project to Guarantee Better Security for Open-Source Projects||Aug 27, 2015|
|Concerning Containers' Connections: on Docker Networking||Aug 26, 2015|
- Using tshark to Watch and Inspect Network Traffic
- September 2015 Issue of Linux Journal: HOW-TOs
- Concerning Containers' Connections: on Docker Networking
- Problems with Ubuntu's Software Center and How Canonical Plans to Fix Them
- Where's That Pesky Hidden Word?
- A Project to Guarantee Better Security for Open-Source Projects
- Firefox Security Exploit Targets Linux Users and Web Developers
- Build a “Virtual SuperComputer” with Process Virtualization
- My Network Go-Bag
- Calling All Linux Nerds!