VLAN Support in Linux
In the case of a VLAN with only a single switch, no Tagged packets should be sent or received. However, it's still useful to think of the Tagging and Untagging as occurring:
Packet arrives and is Tagged according to the PVID of the ingress port.
Egress port is determined based on the VID in the Tag.
Packet is Untagged and sent.
All packets start out as Untagged when they enter the network, and they also should always end as Untagged when they leave the network and arrive at their destination. Along their journey, if they cross a VLAN network, they will be Tagged with a VID, switched according to this VID by one or more VLAN switches, and then finally Untagged by the last VLAN switch.
If you've been keeping track, you know there are three things you need to configure for each port of each switch:
Member VLANs (list of VIDs).
PVID (must be one of the member VLANs).
Whether packets should be left Tagged or Untagged when sent (egress).
With one or more switches, you can achieve any VLAN topology by selectively configuring the above three settings on each port.
A VLAN switch is really just a normal switch with some extended functionality. Before you can have a VLAN switch, you first need to have a normal switch. Fortunately, Linux already has full support for this—it's just not called “switching”.
The functionality that makes Linux what you would think of as a “switch” is called bridging, a more specific and accurate term, because it's based on the official bridge standard, IEEE 802.1D.
For all practical purposes, switches and bridges are the same thing. Switch is a loose term coined by the industry that means different things for different products (for example, $10 switches usually don't fully support 802.1D, while $500 switches usually at least support 802.1D, plus lots of other features).
An 802.1Q VLAN switch is really a VLAN bridge, because 802.1Q as a standard just extends 802.1D (all devices that support 802.1Q must also support 802.1D). Technically, VLAN bridge is the correct terminology, but very few people would know what that means.
In order to use bridges in Linux, you need a kernel compiled with CONFIG_BRIDGE and the userland package bridge-utils. I suggest you also add the ebtables kernel options and userland tool.
Think of each Ethernet interface in your system as a one-port switch. An Ethernet interface already performs the same basic functions as a switch—forwarding packets, maintaining an ARP cache and so on—but on a single port without the need or capability to decide to which other port(s) a packet should be sent.
Linux's bridging code elegantly plugs in to and extends the existing functionality by letting you define bridges as virtual Ethernet interfaces that bundle one or more regular Ethernet interfaces. Each interface within the bridge is a port. In operation, this is exactly like ports of a switch.
The userland tool for administering bridges is brctl. Here's how you would set up a new bridge comprising eth0 and eth1:
brctl addbr br0 brctl addif eth0 brctl addif eth1 ip link set br0 up
Once you run these commands, you'll have a new Ethernet interface named br0 that is the aggregate of both eth0 and eth1. For typical usage, you wouldn't configure IP addresses on eth0 and eth1 anymore—you would now use br0 instead.
The best way to understand how this works is to imagine br0 as a physical Ethernet interface in your box that's plugged in to a three-port switch on your desk. Because br0 is plugged in to one of the ports, this would leave the switch with two remaining ports—eth0 and eth1 are these two switch ports (Figure 1).
Packets will pass between the interfaces/ports, the bridge will learn and maintain an ARP cache, and like a switch, it will decide to which ports each packet should be forwarded.
But, unlike a normal switch external to your system, you own and control all of the ports. You now can use any and all of the tools available under Linux to create the ultimate managed switch!
Because you still have access to the underlying Ethernet interfaces, you can do things like sniffing with tcpdump or snort on ports individually. Using the ebtables package, you can filter the Ethernet packets that pass through your switch with the same control and precision as iptables for IP packets.
Topics such as ebtables are beyond the scope of this article, but see the ebtables man page and Web site (see Resources).
|Free Today: September Issue of Linux Journal (Retail value: $5.99)||Sep 27, 2016|
|nginx||Sep 27, 2016|
|Epiq Solutions' Sidekiq M.2||Sep 26, 2016|
|Nativ Disc||Sep 23, 2016|
|Android Browser Security--What You Haven't Been Told||Sep 22, 2016|
|The Many Paths to a Solution||Sep 21, 2016|
- Android Browser Security--What You Haven't Been Told
- Readers' Choice Awards 2013
- Epiq Solutions' Sidekiq M.2
- Nativ Disc
- The Many Paths to a Solution
- Synopsys' Coverity
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- Returning Values from Bash Functions
- Securing the Programmer
Pick up any e-commerce web or mobile app today, and you’ll be holding a mashup of interconnected applications and services from a variety of different providers. For instance, when you connect to Amazon’s e-commerce app, cookies, tags and pixels that are monitored by solutions like Exact Target, BazaarVoice, Bing, Shopzilla, Liveramp and Google Tag Manager track every action you take. You’re presented with special offers and coupons based on your viewing and buying patterns. If you find something you want for your birthday, a third party manages your wish list, which you can share through multiple social- media outlets or email to a friend. When you select something to buy, you find yourself presented with similar items as kind suggestions. And when you finally check out, you’re offered the ability to pay with promo codes, gifts cards, PayPal or a variety of credit cards.Get the Guide