Hack and / - Linux Troubleshooting, Part II: Local Network
This column is the second in a series dedicated to one of my favorite subjects: troubleshooting. Because my column is generally aimed more at tips and tricks and less on philosophy and design, I'm not going to talk much about overall approaches to problem solving. Instead, in this series, I describe some general classes of problems you might find on a Linux system, and then I discuss how to use common tools, most of which probably already are on your system, to isolate and resolve each class of problem.
In the first column, I talked about how to diagnose high-load issues on a server, but the fact is that these days, just about every Linux computer is connected to a network, and a large number of the problems you have are based in the network. This month, I focus on local network troubleshooting, and although I am writing from the perspective of servers, most of these steps will apply to any Linux machine on a network. Also, because the goal of this article is to show how to become better at troubleshooting, I list each step from the lowest level on up. In real life, I'd probably skip ahead here and there to make the troubleshooting process faster.
The generic problem I cover here is how to track down the root cause when one machine can't communicate with another machine on the same network. For this example, let's assume I have two servers named bill and shawn. The server shawn is trying to communicate with bill over port 25 (port 25 is used for sending e-mail over SMTP), but wouldn't you know it, bill isn't responding.
One of the first things I might do in a scenario like this is find another machine on the same network and try to connect with bill from there. If I can talk to bill from another machine on the same network, the problem is most likely with shawn or with the network in between shawn and bill. If I have the same problem from another machine on the same network, it's more likely that the problem is with bill, so I would start troubleshooting from there. Just so I can discuss more troubleshooting steps, let's start troubleshooting from shawn.
One of the most embarrassing things in troubleshooting is to waste an hour only to find out that something wasn't plugged in. So the first step I perform is to make sure that shawn is plugged in to the network. Although I could inspect the port physically on the server, if the server were in a different city, I might run a program like ethtool. ethtool gives you a lot of different diagnostics on your Ethernet devices. By default, all you have to do is run ethtool as root and pass the Ethernet device you want to check as an argument. In many cases this will be eth0:
$ sudo ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pg Wake-on: d Current message level: 0x000000ff (255) Link detected: yes
As you can see, ethtool gives all sorts of information, including the fact that this machine supports 10 base T, 100 base T and gigabit networking speeds, but it currently communicates at 100 base T, full duplex. To check for a link, just look at the very last line that says “Link detected”. As you can see in my example, link is detected, so my cable is plugged in and I can move on.
Before I move past ethtool completely, it's worth mentioning that it does a lot more than just diagnose link problems. A common problem I've found on networks is a host with slower-than-normal network speeds. Often you'll see this crop up after a reboot or a power outage. What often happens is that when the interface connects to the network, it will try to auto-negotiate the fastest speed it can. Sometimes auto-negotiation doesn't work correctly, in which case the interface might fail back to half duplex mode or might even fail back to 10 base T! If you know that your network can support 100 base T at full duplex, you can use ethtool to disable auto-negotiation and force full duplex. To do this for eth0, you would type:
$ sudo ethtool -s eth0 autoneg off duplex full
Kyle Rankin is a VP of engineering operations at Final, Inc., the author of a number of books including DevOps Troubleshooting and The Official Ubuntu Server Book, and is a columnist for Linux Journal. Follow him @kylerankin.
|Nativ Disc||Sep 23, 2016|
|Android Browser Security--What You Haven't Been Told||Sep 22, 2016|
|The Many Paths to a Solution||Sep 21, 2016|
|Synopsys' Coverity||Sep 20, 2016|
|Naztech's Roadstar 5 Car Charger||Sep 16, 2016|
|RPi-Powered pi-topCEED Makes the Case as a Low-Cost Modular Learning Desktop||Sep 15, 2016|
- Readers' Choice Awards 2013
- Android Browser Security--What You Haven't Been Told
- Download "Linux Management with Red Hat Satellite: Measuring Business Impact and ROI"
- The Many Paths to a Solution
- Nativ Disc
- Synopsys' Coverity
- Naztech's Roadstar 5 Car Charger
- Securing the Programmer
- CodeLathe FileCloud Google Chrome Extension
- Identity: Our Last Stand
With all the industry talk about the benefits of Linux on Power and all the performance advantages offered by its open architecture, you may be considering a move in that direction. If you are thinking about analytics, big data and cloud computing, you would be right to evaluate Power. The idea of using commodity x86 hardware and replacing it every three years is an outdated cost model. It doesn’t consider the total cost of ownership, and it doesn’t consider the advantage of real processing power, high-availability and multithreading like a demon.
This ebook takes a look at some of the practical applications of the Linux on Power platform and ways you might bring all the performance power of this open architecture to bear for your organization. There are no smoke and mirrors here—just hard, cold, empirical evidence provided by independent sources. I also consider some innovative ways Linux on Power will be used in the future.Get the Guide