Hack and / - Linux Troubleshooting, Part II: Local Network

Last month, I discussed localhost troubleshooting, and this month, I extend troubleshooting to your local network. Find out why shawn can't talk to bill.

This column is the second in a series dedicated to one of my favorite subjects: troubleshooting. Because my column is generally aimed more at tips and tricks and less on philosophy and design, I'm not going to talk much about overall approaches to problem solving. Instead, in this series, I describe some general classes of problems you might find on a Linux system, and then I discuss how to use common tools, most of which probably already are on your system, to isolate and resolve each class of problem.

In the first column, I talked about how to diagnose high-load issues on a server, but the fact is that these days, just about every Linux computer is connected to a network, and a large number of the problems you have are based in the network. This month, I focus on local network troubleshooting, and although I am writing from the perspective of servers, most of these steps will apply to any Linux machine on a network. Also, because the goal of this article is to show how to become better at troubleshooting, I list each step from the lowest level on up. In real life, I'd probably skip ahead here and there to make the troubleshooting process faster.

bill Is Down

The generic problem I cover here is how to track down the root cause when one machine can't communicate with another machine on the same network. For this example, let's assume I have two servers named bill and shawn. The server shawn is trying to communicate with bill over port 25 (port 25 is used for sending e-mail over SMTP), but wouldn't you know it, bill isn't responding.

Does shawn or bill Have a Problem?

One of the first things I might do in a scenario like this is find another machine on the same network and try to connect with bill from there. If I can talk to bill from another machine on the same network, the problem is most likely with shawn or with the network in between shawn and bill. If I have the same problem from another machine on the same network, it's more likely that the problem is with bill, so I would start troubleshooting from there. Just so I can discuss more troubleshooting steps, let's start troubleshooting from shawn.

One of the most embarrassing things in troubleshooting is to waste an hour only to find out that something wasn't plugged in. So the first step I perform is to make sure that shawn is plugged in to the network. Although I could inspect the port physically on the server, if the server were in a different city, I might run a program like ethtool. ethtool gives you a lot of different diagnostics on your Ethernet devices. By default, all you have to do is run ethtool as root and pass the Ethernet device you want to check as an argument. In many cases this will be eth0:

$ sudo ethtool eth0
Settings for eth0:
     Supported ports: [ TP ]
     Supported link modes:   10baseT/Half 10baseT/Full 
                               100baseT/Half 100baseT/Full 
                               1000baseT/Half 1000baseT/Full 
     Supports auto-negotiation: Yes
     Advertised link modes:  10baseT/Half 10baseT/Full 
                               100baseT/Half 100baseT/Full 
                               1000baseT/Half 1000baseT/Full 
     Advertised auto-negotiation: Yes
     Speed: 100Mb/s
     Duplex: Full
     Port: Twisted Pair
     PHYAD: 0
     Transceiver: internal
     Auto-negotiation: on
     Supports Wake-on: pg
     Wake-on: d
     Current message level: 0x000000ff (255)
     Link detected: yes

As you can see, ethtool gives all sorts of information, including the fact that this machine supports 10 base T, 100 base T and gigabit networking speeds, but it currently communicates at 100 base T, full duplex. To check for a link, just look at the very last line that says “Link detected”. As you can see in my example, link is detected, so my cable is plugged in and I can move on.

Before I move past ethtool completely, it's worth mentioning that it does a lot more than just diagnose link problems. A common problem I've found on networks is a host with slower-than-normal network speeds. Often you'll see this crop up after a reboot or a power outage. What often happens is that when the interface connects to the network, it will try to auto-negotiate the fastest speed it can. Sometimes auto-negotiation doesn't work correctly, in which case the interface might fail back to half duplex mode or might even fail back to 10 base T! If you know that your network can support 100 base T at full duplex, you can use ethtool to disable auto-negotiation and force full duplex. To do this for eth0, you would type:

$ sudo ethtool -s eth0 autoneg off duplex full

______________________

Kyle Rankin is a systems architect; and the author of DevOps Troubleshooting, The Official Ubuntu Server Book, Knoppix Hacks, Knoppix Pocket Reference, Linux Multimedia Hacks, and Ubuntu Hacks.

White Paper
Linux Management with Red Hat Satellite: Measuring Business Impact and ROI

Linux has become a key foundation for supporting today's rapidly growing IT environments. Linux is being used to deploy business applications and databases, trading on its reputation as a low-cost operating environment. For many IT organizations, Linux is a mainstay for deploying Web servers and has evolved from handling basic file, print, and utility workloads to running mission-critical applications and databases, physically, virtually, and in the cloud. As Linux grows in importance in terms of value to the business, managing Linux environments to high standards of service quality — availability, security, and performance — becomes an essential requirement for business success.

Learn More

Sponsored by Red Hat

White Paper
Private PaaS for the Agile Enterprise

If you already use virtualized infrastructure, you are well on your way to leveraging the power of the cloud. Virtualization offers the promise of limitless resources, but how do you manage that scalability when your DevOps team doesn’t scale? In today’s hypercompetitive markets, fast results can make a difference between leading the pack vs. obsolescence. Organizations need more benefits from cloud computing than just raw resources. They need agility, flexibility, convenience, ROI, and control.

Stackato private Platform-as-a-Service technology from ActiveState extends your private cloud infrastructure by creating a private PaaS to provide on-demand availability, flexibility, control, and ultimately, faster time-to-market for your enterprise.

Learn More

Sponsored by ActiveState